Solving ANSYS Contact Problem for FEA of Rail Fastening Systems

  • Thread starter Thread starter albertop
  • Start date Start date
  • Tags Tags
    Ansys Contact
AI Thread Summary
The discussion focuses on using ANSYS Workbench for Finite Element Analysis (FEA) of rail fastening systems under dynamic loads. Key challenges include defining the contact area between the clip and angle guide plate, which changes due to deformation under load. Recommendations for solving the contact problem include improving mesh quality, using frictionless contact conditions initially, and selecting appropriate contact formulation settings. Additionally, a denser mesh and numerous substeps are advised for accurate results. The conversation highlights the complexity of contact settings in ANSYS, particularly for users new to the software.
albertop
Messages
2
Reaction score
0
I'm currently writing my thesis on a "Finite Element Analysis of rail fastening systems under dynamic load", and I'm using ANSYS Workbench 14.0 for that matter.

I don't know how to define the contact area for the clip and the angle guide plate, since it will be changing over time as the clip (and the plate) deform due to the loads applied.
http://imgur.com/xbLPbOl
http://imgur.com/eVhZB6G

This picture shows the existing gap between them, for you to see the future contact areas:
http://imgur.com/YdmPnxy

The CAD data for both objects were obtained with a 3D scanner, which means that the surfaces are neither smooth nor perfectly fitting to each other.

I'm too experienced with ANSYS; therefore a thorough answer will be greatly appreciated!

Thank you in advance!
 
Engineering news on Phys.org
There is a lot to consider, you'll have to get into the gritty details of the contact conditions if you hope to defend the thesis. From a high level, the main considerations you should address from what I'm seeing:

  • You should clean up your mesh by inserting a "Method" object in the mesh portion of the problem tree, and select "hex dominant." This will give you a quad-primary mesh. You're also going to want a much denser mesh than what you have right now.
  • I would select frictionless contact conditions for a start, and then add friction as you have a reliably converging problem setup. Make sure you select your coefficient of friction carefully though, it can vary wildly with subtle changes in material and surface finish.
  • Select "augmented lagrange" for your contact condition formulation, make sure the contacts update every substep, and have "automatic bisection" active.
  • Make sure you have similarly sized elements on both sides of the contact condition using a "contact sizing" mesh element.
  • Substeps: you'll want a lot of them. Possibly hundreds.

That should give you a good start anyway.
 
Hello Mech_Engineer,

Yes, it's kind of a hard project considering I'm pretty new to ANSYS.

Thanks for the advice, I really appreciate it!
 
Ansys 14.5 contact setting help

Hello to all ,
I new to ansys workbench and I am need guidance as to how to do contact settings and how to find the friction between two moving surfaces. Im designing a surgical scissor. Kindly let me know what settings are preferable for contact setting of scissor and how to find friction between surfaces.

thanks for taking time and helping me.
 
How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'
Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
I'd like to create a thread with links to 3-D Printer resources, including printers and software package suggestions. My motivations are selfish, as I have a 3-D printed project that I'm working on, and I'd like to buy a simple printer and use low cost software to make the first prototype. There are some previous threads about 3-D printing like this: https://www.physicsforums.com/threads/are-3d-printers-easy-to-use-yet.917489/ but none that address the overall topic (unless I've missed...
Back
Top