Variable frequency drive for high speed spindle

AI Thread Summary
The discussion focuses on the compatibility of a variable frequency drive (VFD) with a new high-speed spindle for a CNC router table. The current VFD, LS Industrial Systems - Starvert SV008IC5-1F, can handle up to 400Hz but is rated for a maximum output of 0.75kW, while the new spindle requires 1kW. Users suggest that the existing VFD may not be suitable for the new spindle due to this power discrepancy. It is recommended to consider upgrading to a larger model, such as the SV015IC5-1F, to ensure proper functionality. Understanding the specifications of both the VFD and spindle is crucial for optimal performance.
Icestation2
Messages
3
Reaction score
0
I operate a CNC router table with a high speed spindle. I'm looking to upgrade to a new spindle but need to know if the variable frequency drive I currently have will work with this new spindle.

The new spindle has the following stats: 300Hz, 1kw, 18000RPM.

The frequency drive is made by LS Industrial Systems - Starvert SV008IC5-1F

The info on their website suggests that this particular drive can reach 400HZ, but I’m not sure about the other details, especially whether or not 1kw is too high.

More info is available using this link:

http://eng.lsis.biz/product/product/introduce/ecatalog_viewStream.asp?catalog_id=288&fileNum=1

Any advice would be welcome.
 
Last edited by a moderator:
Engineering news on Phys.org
Cool to see another CNC person here, I've did my own X2 CNC Mill conversion recently.

The "008" of "SV008IC5-1F" says it's 0.75 kw time to upgrade to get those faster IPM speeds.

btw have you tried CNCzone.com before, people there are good at answering CNC stuffs like this.
 
I'm wondering if the 0.75KW motor rating - as shown in the PDF manual - relates to the motor within the frequency drive, and not it's output. Does anyone know if a frequency drive has a motor? My knowledge of these devices is quite poor.
 
Icestation2 said:
I'm wondering if the 0.75KW motor rating - as shown in the PDF manual - relates to the motor within the frequency drive, and not it's output. Does anyone know if a frequency drive has a motor? My knowledge of these devices is quite poor.
The specs indicate the rating for the motor being driven. Looks like the model you are considering (SV008IC5-1F) would drive a 1 HP (0.75kW) load. If your spindle motor is rated at 1kW then I would consider something a little larger; maybe the SV015IC5-1F.
 

Thread 'What happens if shielded cable has short to the shield?'

While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
View full post »

Thread 'Underwater piezoelectric sensor array receive sensitivity'

Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
View full post »

Thread 'Question about bonding ground and neutral'

I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
View full post »

Similar threads

Variable Frequency Drive vs. Servo Drive
Replies
3
Views
12K
Can Variable Frequency Drives Control Both Speed and Torque Simultaneously?
Replies
2
Views
2K
Federal A/C Unit Efficiency Standard Up
Replies
1
Views
5K
Programs Math minor, double major, and elective classes advice
Replies
4
Views
3K
Hydrogen-boron High Density Plasma Toroid Fusion
Replies
3
Views
4K

Hot Threads

Recent Insights

Back
Top