Flow rate Definition and 464 Threads

Homework Statement An turbine expands air at 1300 kPa and 500oC to 100 kPa and 127oC. Air enters the turbine through a 0.2-m2 opening with an average velocity of 50 m/s, and exhausts through a 1-m2 opening. Determine (a) the mass flow rate of air through the turbine Homework Equations PV=RT m...

Sir, Kindly let me know how to calculate flow rate (cfm or Litre/m) of air flowing through a pipe of 12 mm dia from a reservoir at pressure 7 kg/cm2 to atmosphere. i.e ;- how much volume of compressed air could pass within a minute through a "X"mm dia pipe from a constant pressure (7 kg/cm2)...

Homework Statement Imagine that you are blowing air through a straw in a cup of water and the root of the straw was connected through a rectangular box with empty base and every side of the rectangular box was cut into "teeth" shape. Bubbles will come out from the teeth of the rectangular box...

I'm really confused by this question, as it is different than the examples we did in class. I've compared my answer with a few classmates and I'm getting a different one, so I'm not sure if I've done it wrong or if they have. I'd really just like to know if I am on the right track! Thank you :)...

Attempting to determine the torque on the shaft of a pump. Known values are flow rate, RPM, and shaft diameter. 1. What other values are needed to make the calculation? 2. What is the equation I can use for this?

Homework Statement At a processing plant, olive oil of density 875 kg/m3 flows in a horizontal section of hose that constricts from a diameter of 2.92 cm to a diameter of 1.20 cm. Assume steady, ideal flow. What is the volume flow rate if the change in pressure between the two sections of hose...

Hi, I'm building an experimental set-up for some heat exchanger I'm trying to analyze, I want to maximize the flow through this little piece. I have a stable temperature bath, (see picture) that has an evacuation valve on the bottom. I only took introduction to Fluid Dynamics (found it amazing...

I am currently designing a lubrication system which uses a positive displacement gear pump. So how can I get the flow rate of a lubrication system? i don't know which equation to use. thank you so much.

Hello everyone, i am currently dimensioning a compression system using a vehicle turbocharger and need to find a way to relate the pressure ratio of the compressor and the mass flow rate. (flows trough compressor and turbine are of course separated) For the turbine, one can use Stodola's...

I've always been taught that in a piping system (only water), if the flow rate doubles, then pressure loss quadruples. But when using the Darcy-Weisbach equation I often find that it is closer to triple. Playing around with viscosity and temperature I've never been able to bring the ratio higher...

Hi, I used a blower to flow air across an open duct through a nozzle. By using a gate valve, the mass flow rates were controlled. I took measurement in 3 different locations along the ducts. But, why by decreasing the mass flow rate, the air velocity was increased? It is just happened for the...

Homework Statement Basically I'm given a feed flowrate - 70,000 gal/day I know the weight percent is 35% and the component is Triethylene Glycol - density - 1.255g/ml Homework EquationsThe Attempt at a Solution So i did this 70,000 gal/day * .35 * (.0378mL/1gal)* 1.255g/mL = g of Triethylene...

Homework Statement A tank of cross-sectional area A is initially filled with fluid of density ρ and viscosity μ to height hi. The pressure above the fluid in the tank is atmospheric, Patm. At the base of the tank there are two pipes, which are both open to teh atmosphere, such that fluid...

Hi everyone, I am an electrical engineering student and in my free time, I make educational youtube videos about electronics. (youtube.com/SolidStateWorkshop). I'm working on a video right now about transistors. To help explain their operation, I am attempting to use a hydraulic circuit...

Homework Statement A patient, on an anesthetic, is hooked up with only 18 mg of the anesthetic remaining. If the current flow is 12 mg/h and the dentist needs to increase the flow to 20.0 mg/h within two minutes, then how long will it take for the anesthetic to run out? Homework Equations...

I know that F=ma which give the units of kg.m/s/s (in SI units) but can force also be expressed as mass flow rate times velocity which also has the same units? Example: water coming out a hose or gas coming out a spray can?

< Mentor Note -- thread moved to HH from the technical forums, so no HH Template is shown >[/color] The max flow rate through a control valve with an equal percentage characteristic is 10 m3/h. If the valve has a rangeability ratio of 50:1 and is subjected to a constant differential pressure...

I want to calculate the flow rate from flow coefficient (cv ) ,so i need the testing methodology and procedure .please give an idea to clarify my doubts.

So we all know that due to the conservation of volume flow rate, reducing the diameter of a hose pipe would increase the velocity of the water flow.(A*V is conserved) But when the are of an orifice near the bottom of a water tank is reduced the velocity remains the same! Does anyone know why...

Hi guys, quick simple question. Lets say I have a pipe separated into 3 sectoins (all horizontal), all have the same flow areas. In the first section it is all liquid water. I know the mass flow rate in this. In the second section the water is heated. And I can work out the steam quality...

I have a condenser with a mass flow rate of 60kg/s, an initial point 1: P=50kPa, Quality = 95% and a final point 2: P = 50kPa that is saturated liquid. cooling water flows through the condenser with a mass flow rate of m(dot) and has a delta temperature of 15 degrees Celsius. how do i...

hello In venturi meters, orifice plate meters and generally when there is a neck, constriction at a point in a pipe there is, at that point, a drop in pressure and an increase in velocity, so that the whole energy is preserved (theoretically) my question is, why if we increase the flow rate...

I am in need of a formula to calculate mass flow rate of liquids through a known orifice size and known pressure/secondary pressure. I need to do this for multiple liquids and I know the specific gravity for each liquid. can anyone help with this formula.

Homework Statement A hose with a nozzle 80 mm in diameter ejects a horizontal stream of water at a reate of 0.044 m3 s-1. With what velocity will the water leave the nozzle? What will be the force exerted on a vertical wall situated close to the nozzle and at right-angles to the stream of...

I've Attached the question and my answer to question 1 to task 3 and guidance if I've done it right? Or any guidance?

How to calculate how much flowrate from blower i can push water pool 2,75m*1,8m down by 1,25m in 1 sec? Note : Blower Pressure 0.03 bar - 0.035 bar There is an empty room above the water pool with dimension of 2.75m*1.8m*1.7m This process happen in a closed chamber...

Hello everyone, I'm new to this forum and this is my first post so go easy! I have an engineering problem which I am uncertain as to how to solve. I am trying to design a basic ballast system for pumping seawater. The idea is to use compressed air to evacuate the water through a series of...

Does the mass flow rate differ depending on whether it's after the feedwater heaters or before the turbines or is it just constant throughout the entire system?

Hello everyone, I am quite new to Fluid dynamics, so I would like to ask for your help. Is it possible to calculate volumetric flow rate from the instantaneous pressure? We need to know the flow rate of the air entering the cylinder in the engine due to the suction pressure. It is required to...

Hi, even though it seems so simple; I can't solve this since a few days and it's driving me crazy. Flow gets inside the tube from point 1, it will create a vacuum, which will let a secondary flow inlet from point 2. Both flows will mix inside the tube, and get out of the junction from point...

Is flow rate at inlet of pressure regulator ( not relief valve) equal to flow rate at outlet ?

Hello guys, I need to calculate the flow rate for the following system. 2 lines of CO2 cyclinders at 60 bar. Each line (1/2'') goes to a 1/2'' PSV valve. Downstream the 2 PSV the line are collected together into 1'' pipe. The two PSV are identical and as per datasheet they have the following...

Hi. First of all, I should mention that I'm quite a novice in both physics and engineering. Let's consider an hourglass (or a silo) that is inclined at a constant angle. I'm unsure of how to calculate the necessary diameter of an orifice for a given mass or volume of granular matter to...

Currently i have a system using bulk argon and i am changing to nitrogen. To trial this i am going to use cylinders of OFN(oxygen free nitrogen). how do i caculate how many cylinders i need based on a flow rate of 16 liters/min. Thanks

Hello there, so I have answered my question from fluid systems but the answer doesn't look right ;/ and I have no idea what have I done wrong. Can you please check and correct where it's wrong ? ;) here is the question: A pipe contains a gradually tapering section in which its diameter decreases...

I am confused about the relation of mass flow rate with different mach numbers in a compressible flow. In wikipedia (http://en.wikipedia.org/wiki/Choked_flow), I read the following: "Although the gas velocity reaches a maximum and becomes choked, the mass flow rate is not choked. The mass flow...

I'm trying to get a rough idea of how flow rate through a round, sharp edged orifice is affected when a fluid is water/glycol versus pain water. In this circumstance, it's 30% water, 55% Dihydroxydiethyl Glycol and 15% Polyalkylene Glycol. I don't need exact numbers at this point, just a...

Hi, I have a question regarding the flow rate in a pipe. According to the general rule the flow rate is: Q = v * A where Q [m3/s] v [m/s] A [m2] So according to this formula the flow rate depends only on the inner area of the pipe and the velocity of the fluid and does...

Homework Statement Hello, I have really hard time to express the gas law PV=nRT to PQ=ṁRT where Q is volumetric flow rate and ṁ- mass flow rate. Is it possible ? Teacher told me, it is ... Homework EquationsThe Attempt at a Solution

Hi, I'm not sure if I'm posting in the right spot but I'm going to guess this is an easy question for you all. I'm going to give as much detail as I can, maybe too much.. My 2 family house condo has a single 2" or 3" water supply from the street. It is split to supply the first floor and...

I'm designing a testing unit where I need to estimate the smallest diameter of a short complex pipe (around 1 meter, three bends and some diameter viariations). Since the pipe is being cooled down in a water bath after production, my idea is to force water with a known pressure in one end of the...

I am interested in mass flow rate in conveyor screw transportation http://www.colormaxsystems.com/wp-content/uploads/2013/11/5-screws-300x222.jpg any recommended book,engineering guides ?

Is it possible to calculate the max flow rate (gals/m) achievable through a given piping system with only the following variables? - 4" SDR 11 HDPE pipe (3.633" ID) - 28,000 feet of pipe from source to destination - 90' of elevation change from source to destination - destination is another...

Hi I need to work out a flow rate of a fire hydrant in Liters per second. I know the pressure is 3.5bar and the pipe diameter is 100mm Any help would be appreciated Thanks

If I have a pump of 50psi and 2L/min flow rate and it is connected to a nozzle. The nozzle catalogue specs for example shows that : 40psi = 0.5L/min 50psi = 0.6L/min 60psi = 0.7L/min Is flow rate at the nozzle output 0.6L/min? Regardless of the pump flow rate, as long as pressure are same...

Hey guys, can some of ou help me with this question: I need to calculate the volumic flow rate for air by using the ideal gas law. Things i know from the assignment: molarmass = 28,96 kg/kmol Pressure = 1 bar mass flow = 2 kg/s t in = 20 degrees celcius t out = 50 degrees celcius (sorry for bad...

I'm new here, and I have a question that might be easy but really confuses me. Does the volumetric flow rate of incompressible fluid change across a valve?. Based on my analysis, no it can not change since the mass is conserved, and since it's incompressible fluid. I know that the velocity will...

I've noticed that certain propane torches will have a seemingly linear relationship between their PSI and BTU/hr. IE, 18 PSI -> 220,000 BTU/hr. From this a person could calculate how much gas is being burned per sec/minute/hr. So, is there a general relationship/formula that I can use to...

I am looking at air system that is under a constant pressure of 350 mbar into a pipe that has 40 - 2 mm round holes. Is there a formula that I can use to calculate the total volume of air nm3/hr that will escape the system? Let's just say the air temp is constant. Can anyone help with this?

I am trying to find out what is the best method / correct formula to calculate Flow rate at inlet/outlet when pressure is known. Please see attached image. any help would be greatly appreciated. Note: Flow Rate can Vary from 100 sccm to 500 sccm.