Dynamics/Kinematics - Jumper beats record jump

  • Thread starter Thread starter azukibean
  • Start date Start date
  • Tags Tags
    Jump
AI Thread Summary
The jumper, weighing 60 kg, aims to exceed a record jump of 1.1 m by bending her knees 0.5 m before launching. The necessary launch speed to reach the apex is calculated as 4.69 m/s, derived from the kinematic equation. To find the required jump force, the net force equation is applied, resulting in an acceleration of approximately 22 m/s². This leads to a calculated jump force of 1920 N, factoring in her weight. The discussion emphasizes the importance of correctly defining initial conditions in kinematic equations for accurate results.
azukibean
Messages
18
Reaction score
0

Homework Statement


The jumper is 60 kg and wants to beat the school's record jump, 1.1 m. She bends her knees a distance of .5 m before jumping. How many Newtons must Fjump be to for her to beat the record?

Homework Equations


ma = ƩF
V2 - V02 = 2a(X - X0)

My teacher stated I would just need these two equations, and that I would use the latter twice.

The Attempt at a Solution


Jumping up to the apex:
02 - 02 = (2)(-10)(1.1)
She jumps up from rest and the velocity of a mass at the apex is zero; right after she jumps, the only force acting on her is gravity, which is -10 m/s2. I assume 1.1 to be X because she can beat the previous runner's score if she jumps 1.1000001 m, essentially 1.1. So in my solution I could say "she has to jump with a force great than _X."

60a = Fjump - 600
I need acceleration from the previous step.

a) I don't know how to work in the .5 m into the equations. Would I add .5 to X? I would still get a nonsensical answer for step 1.
b) What is wrong with step 1's set up?
 
Physics news on Phys.org
The problem with step 1 is with your definition of "initial". The v0 in your equation is not the speed at the beginning of the jump. It's the launch speed: the speed at the end of the jump, once the jumper's legs are straight and she leaves the ground. And v is the final speed, the speed at the apex, which is 0. So, we have:

v0^2 = -2gh, where h = 1.1 m, the desired height of the jump.

Okay, that's all well and good, and from this we can find the launch speed needed.

How do we get the jump force? That's step 2, where we apply the kinematics equation again. It must be that the acceleration from the net force Fjump - weight, applied over a distance of 0.5 m, gives you a final v that is equal to v0 from step 1. So, in *step 2*, "initial" now means at the beginning of the jump. So v0 = 0, and v = the needed launch speed from step 1, and d = 0.5 m. From this you can solve for 'a', which gives you Fnet.
 
Cepheid variable!
---
Straight legs:
v0^2 = 2*-10*1.1
v0 = 4.69

Bent:
4.69^2 - 0^2 = 2*.5*a
a = 21.996

60*22 = F(jump) - 600
F(jump) = 1920 N
---
Thanks!
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top