How Can a Backup Generator Automatically Support Two Different 3-Phase Grids?

  • Thread starter Thread starter abdelhamid
  • Start date Start date
  • Tags Tags
    Power Sources
AI Thread Summary
To automatically support two different 3-phase grids with a backup generator, a proper connection setup is essential. An automatic transfer switch (ATS) is required to switch the load to the generator when either grid loses power. The ATS monitors the grid status and ensures the generator starts up seamlessly when needed. Proper installation and configuration of the ATS will guarantee reliable operation and load management between the two grids. This setup enhances energy security and minimizes downtime during power outages.
abdelhamid
Messages
1
Reaction score
0
we are planning to install one backup generator to secure two differenr grids 3 phase each.
how shall be the connection that gurantee if any source of the two grids is off, the generator will automatically start up and take the load??
 
Engineering news on Phys.org
You would need a http://en.wikipedia.org/wiki/Transfer_switch" .

For example: http://www.apelectric.com/ASCO-300-Series-200A-Automatic-Transfer-Switch-p/asco-300-200a.htm?gdftrk=gdfV21065_a_7c276_a_7c712_a_7cASCO_d_300_d_200A"
 
Last edited by a moderator:

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

Self excited induction generators and grid connected solar inverters?
Replies
9
Views
2K
How is power limited from renewable sources
Replies
10
Views
2K
Power grid & generator questions
Replies
46
Views
6K
How are coils arranged in a power station generator?
Replies
8
Views
4K
A little help understanding 3 phase waveforms and summation
Replies
5
Views
2K
AC generator output voltage to grid question
Replies
4
Views
2K
Convert 1 phase to 3 phase by using an old washing machine
Replies
19
Views
3K
Combining 2 grid connections ac to one
Replies
2
Views
1K
ABC reference frame synchronous generator modelling in Ltspice
Replies
1
Views
3K
How Can I Design an Off-Grid Solar System with Panels on Multiple Roofs?
Replies
2
Views
1K

Hot Threads

Recent Insights

Back
Top