How Can Helium Balloons Help in an Egg Drop Project?

AI Thread Summary
Helium balloons were considered for an egg drop project, but the limited capacity of a grocery bag restricted their use. Initial attempts with styrofoam failed, resulting in a cracked egg from a height of 7-8 feet. A successful design involved using a can cooler, layering plastic bags, and securing helium balloons, which slowed the descent. The egg survived a drop from over 50-60 feet, surprising peers who doubted the effectiveness of the small setup. The project demonstrated that creative solutions can lead to success in science challenges.
swimmingfreak
Messages
2
Reaction score
0
yes this is an egg drop project once again, i had the idea to use helium balloons, but the problem is that the whole thing must fit in a grocery bag. only two balloons fit in a grocery bag! that can't carry very much! we can't use paracutes, otherwise we can do anything. i tried just now to cut a square piece of styrofoam and put the egg insided a hole i made in it. a tied the two balloons to the square and dropped it. the egg rolled out of it and cracked, and that was from a hieght to about 7-8 feet! we are dropping them from I'm guessing over 50-60 feet! please help my idea work or help me to think of a new one! the project is due tomorrow! I am usually very good at science, but I am stuck! please help me!
 
Physics news on Phys.org
i remember making somehting to protect an egg for some class, i used a styrofoam from a box which came with my laptop, the foam was very good quality, and i did the whole cude thing, cut the cube in half, amde a place for the egg. and taped it up

to my surprise there was no way for me to hurt the egg, i played a little football with it, if you don't have that kind of foam then, here's what i thought of: take a cordboard box, 5inches cube, (5 x 5 x 5) and layer it with plastic inside, and fill it with water, toss the egg in and tape a plastic bag over it, if it's well made, the box won't leak, and the box will likley explode when it hits the groud, but i think the egg may very well survive. that's just what i thought of...
 
well here is what i did, if anyone wants to know...i took a can cooler and put a plastic bag on the bottom, then i put the egg in a plastic bag and put it in the middle, and on the top i put in, guess what, another plastic bag. i used a needle to pull the thread through three sides of the can cooler, i then tied the strings of the balloons to the thread. we did the egg drop today and my egg survived with no cracks, much to everyones suprise. they all thought it was too small, but the balloons made it go a lot slower than everyone elses! (it didnt float down though) so i did it all by myself because no one decided to reply until it was too late, but that's ok because what i did worked and I'm very proud of myself!
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top