How Long Does It Take for a Wrecking Ball to Fall to the Ground?

AI Thread Summary
A wrecking ball takes 1.2 seconds to fall halfway to the ground after its cable breaks. To calculate the total time for the ball to reach the ground, one can use the equations of motion, specifically ∆Y = VoT + 0.5At², where A is the acceleration due to gravity (approximately 9.81 m/s²). By determining the distance fallen in the first half and using the derived velocity, the total time can be calculated. The discussion emphasizes the importance of understanding the variables and equations involved in solving the problem. Ultimately, the correct approach leads to finding the total fall time effectively.
pstfleur
Messages
29
Reaction score
0
1. A wrecking ball is hanging at rest from a crane when suddenly the cable breaks. The time it takes for the ball to fall halfway to the ground is 1.2 seconds. Find the time it takes for the ball to fall from rest all the way to ground
2. Vf=Vo-gt, Vf^2=Vo^2-2g(delta y), Yf=Yo+Vot-1/2gt^2
3. I first found the velocity of the ball traveling to the halfway mark.
Vf=0m/s-9.8(1.2)=-11.76.. I'm not quite sure how to relate that to the actual question. I wonder if I am even headed in the right direction.
 
Physics news on Phys.org
Hello
Please excuse me because in my physics class we learned with a different set of variables, which seems stupid because on PF i have yet to see anyone use the ones we have haha. Anyway, the equation needed to solve this would be.

∆Y=VoT+.5At2 (i believe A is called g in your equations)

In words this reads... change in y is equal to the initial velocity multipled by time, plus half the acceleration multiplied by the time squared.

So, what you should look to find out, is the change in y of the half of it, which took 1.2 seconds. after you get that, I am sure that you will be well on your way. To check if you do the problem right, the answer i got is sqare root of 2.88 seconds2

Good luck!
 
lax1113 said:
Hello
Please excuse me because in my physics class we learned with a different set of variables, which seems stupid because on PF i have yet to see anyone use the ones we have haha. Anyway, the equation needed to solve this would be.

∆Y=VoT+.5At2 (i believe A is called g in your equations)

In words this reads... change in y is equal to the initial velocity multipled by time, plus half the acceleration multiplied by the time squared.

So, what you should look to find out, is the change in y of the half of it, which took 1.2 seconds. after you get that, I am sure that you will be well on your way. To check if you do the problem right, the answer i got is sqare root of 2.88 seconds2

Good luck!

Thanks, That helped extremely in putting me in the right direction
 
well, downward acceleration on Earth (or g) is always a constant 9.81 m/s2 so ll you have to do is plug into the equation
so just plug that into the equation D = D0 + V0t +(1/2)at2 to find the half of the distance, then double to find the total distance.
then we change the equation v2 = v02 + 2aD so that it can solve for v, v0 is 0 and 1 = g so all we do is remove that, switch a to g, and take the squareroute of both sides snd we get. V = sqrt(2gd), plug in and solve. the use that value as v in the equation v = at (a = g again) and solve for total time
 
Last edited:
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top