Innovative ideas(devices) for common problems

  • Thread starter Thread starter mayank153
  • Start date Start date
AI Thread Summary
Innovative device ideas for societal problems include an automatic crop harvester to aid farmers and a trash compressor to manage waste effectively. A significant focus is on water purification systems to convert non-potable water into safe drinking water, addressing a critical issue in developing countries. Suggestions also include a high-temperature staged furnace for waste management that generates energy while reducing pollution. Additionally, there is interest in creating devices that assist the handicapped and elderly, enhancing their daily lives. The discussion encourages practical and simple solutions to common problems.
mayank153
Messages
2
Reaction score
0
i have to make a working project (basically a machine) , the idea is to take any problem provide its solution (a device ) which is for the welfare of the society .

i m a 2nd year mechanical engineering student

try to give as many ideas as you can!

i doesn't have to be complex even simple one's will do ...
the ideas should just be practically USEFUL.

for example automatic crop harvester for farmers , trash compressor and stair climbing wheel chair for the handicapped etc
please think of ur common day to day problems and try to provide a feasible practical solution
 
Engineering news on Phys.org
One of the largest problems in the world is the lack of drinking water in many developing countries. They have the water, but it's not clean, which can lead to all sorts of diseases, many of which can be fatal when nutrition is also an issue (and it usually is). Maybe you can devise a means to take freshwater (non-saltwater, not necessarily clean) and make it drinkable.

I've been kicking this project around in the back of my head a bit, and I know that a lot of Engineeers without Borders (EWB) groups have been doing similar projects, but it's still a good challenge (and a huge benefit to society). Off hand, I can think of a few requirements you may want to consider:

1) How do you power it
2) How much should it output
3) Cost restrictions?
4) Lifespan

I could get much more detailed, but I really think it would be better if you came up with those yourself (should you choose this project).
 
I think a common day to day problem is students not coming up with their own ideas.
 
RandomGuy88 said:
I think a common day to day problem is students not coming up with their own ideas.

Whatever.

I like BigAggie's idea - water purification. Very simple technology is used to dramatically increase the water supply throughout the world.

One of the most intriguing devices is the http://en.wikipedia.org/wiki/Hydraulic_ram" the water for everything.

mayank153 said:
...for example automatic crop harvester for farmers...

Top of the line crop harvesters are GPS/WAAS guided, with differential GPS inputs for extremely precise guidance.

...trash compressor...

How about a simple, cheap, staged furnace system which both dries the garbage and burns it at very high temps for providing heat and energy while minimizing pollution?

As for common-day problems, one of mine is getting my toilet to flush 100% of it's contents! LoL! I never had this problem in Germany, but their designs had other issues.
 
Last edited by a moderator:
please give some more ideas ! the device can be anything that for example can be used to help the handicapped or the elderly .

please pour in new ideas .anything out of the hat will could be useful!1
 
I need some assistance with calculating hp requirements for moving a load. - The 4000lb load is resting on ball bearing rails so friction is effectively zero and will be covered by my added power contingencies. Load: 4000lbs Distance to travel: 10 meters. Time to Travel: 7.5 seconds Need to accelerate the load from a stop to a nominal speed then decelerate coming to a stop. My power delivery method will be a gearmotor driving a gear rack. - I suspect the pinion gear to be about 3-4in in...
How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
Thread 'Calculate minimum RPM to self-balance a CMG on two legs'
Here is a photo of a rough drawing of my apparatus that I have built many times and works. I would like to have a formula to give me the RPM necessary for the gyroscope to balance itself on the two legs (screws). I asked Claude to give me a formula and it gave me the following: Let me calculate the required RPM foreffective stabilization. I'll use the principles of gyroscopicprecession and the moment of inertia. First, let's calculate the keyparameters: 1. Moment of inertia of...
Back
Top