New realizations or "what I think I learned today"

  • Thread starter Thread starter Planobilly
  • Start date Start date
AI Thread Summary
The discussion centers around the journey of building guitar amplifiers, particularly the successful implementation of a Fender Deluxe Reverb AB763 circuit. The creator overcame challenges related to noise and hum by developing his own grounding schemes, ultimately achieving a clean sound without interference. He emphasizes the importance of critical thinking and personal experimentation over blindly following traditional methods and advice from renowned sources. The conversation also touches on the emotional aspects of learning, highlighting that self-doubt and fear of failure can hinder progress. Overall, the experience underscores the value of hands-on learning and resilience in mastering complex skills.
Planobilly
Messages
440
Reaction score
105
Hi Guys,
As you all know, I have been trying to learn to build excellent guitar amps. Most of my failures have been related to various amounts of hum/hiss and noises in the amps.

The Fender style Deluxe Reverb AB763 circuit I built is finally working just about perfect now. I had a lot of advice from many sources, people, books, the internet. I listen to all that and never got to where I was satisfied with the results.

At the end of the day I implemented my own ideas concerning grounding schemes which finally worked. With all the controls turned up all the way you can only tell if the amp is on by looking at the pilot light. Zero noise, zero hum/hiss. I now have clean clear undistorted sound when I want it and both preamp and output tube distortion when I want it. Man what a pain in the butt learning curve.

To get to that point, I had to disregard the type of components and methods used in the old amps of the sixties and stop repeating the mistakes of a bygone era. I had to stop listening to the nonsense that so many guitar players are so dearly attached too and I include myself in that group...lol

Electronics as far as guitar amps go is extremely unforgiving. I guess all electronics is. Everything has to be dead on. One bad solder joint, one out of value component, one wire 10mm to close to the next and the whole thing just does not function correctly.

I am beginning to think the best thing is to learn everything you can from every source there is and take all information with a grain of salt. Don't assume that the world famous designer is always correct or not. Don't assume anything. Use your own brain and work like hell till you get the results you are looking for.

For the last few weeks I have had some significant self doubts about my ability to learn this stuff. If I live long enough I may just get there...lol

Cheers,

Billy
 
  • Like
Likes jim hardy, dlgoff and Prehistorik Watcher
Engineering news on Phys.org
Bill

Planobilly said:
Use your own brain and work like hell till you get the results you are looking for.

Your adventures are proof positive that we learn 10X more by doing than by reading about doing. Recall Melville's "Consumptive Usher" .

Congratulations on your success .
 
Thanks Jim,

It was a "small" brick in the road to success. The larger success was a greater degree of self confidence. Fear of failure, self doubts, concern for what other people may think, to much need for acceptance, all combine to essentially guarantee failure. Emotional state has a large part to play in anyone succeeding or failing at anything.

Thank you so much for all the help and encouragement you have provided to me.

Cheers,

Billy
 
Planobilly said:
It was a "small" brick in the road to success. The larger success was a greater degree of self confidence. Fear of failure, self doubts, concern for what other people may think, to much need for acceptance, all combine to essentially guarantee failure. Emotional state has a large part to play in anyone succeeding or failing at anything.

One of the pleasures of aging - accepting that those fears are natural and trudging through them.

I still to tell myself "No way out but through... my best is usually good enough , and i'll get better as i go.

Progress not perfection.

There should be FFT in something that you own already. That Rockland is a wonderful analog instrument if you can find one.

That LM359 filter is a great design but with my high Q(around 70) bandpass the board layout became important, just like in your amps. First one was on verge of oscillation.

old jim
 
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...

Similar threads

Back
Top