The rate of evaporation at high temperatures

  • Thread starter Thread starter UOP Student
  • Start date Start date
  • Tags Tags
    Evaporation Rate
AI Thread Summary
A University of Portsmouth student is investigating the evaporation rate of 2 liters of water at 360 degrees Celsius to cool airflow in a venting system. Using the Langmuir evaporation rate equation, the calculated evaporation rate is 0.185 kg/m²/sec, suggesting the water would evaporate in about 108 seconds. However, there is skepticism regarding this rapid evaporation time, as it seems implausibly short given the volume of water and the high temperature. The discussion raises concerns about the accuracy of the calculations and the assumptions made, particularly regarding the ambient conditions and the evaporation process. Further validation through experimentation or additional calculations is suggested to confirm the findings.
UOP Student
Messages
2
Reaction score
0
To whom it may concern
I'm a University of Portsmouth student in the UK and have a conundrum for one of my projects. I'm trying to evaporate a reservoir of water at the bottom of a venting system to cool down the airflow in a gap between two membranes for a period of time. The reservoir is at the bottom of the void and the temperature of the air above the water is 360 degrees C. How long would it be for 2 litres of water to evaporate?
I have looked for a simple solution for this and have come across Langmuir evaporation rate but I'm struggling to make sense of it. If this the correct way forward?
According to my findings I need to use the equation
(mass loss rate)/(unit area)= (vapour pressure- ambient partial pressure)* sqrt((molecular weight)/(2*pi*Gas constant*temperature in Kelvin))
The Surface area (unit Area) of the water will be 0.1m²
the vapour pressure of water at 360 degrees C is 18666
the pressure at ambient (20degrees) is 2.3392
Molecular weight of water is 0.014kg/mole
Gas Constant (R) = 461.5 for water vapour
Temperature in kelvin = 360+273=633

Therefore this would mean through calculus that the rate of evaporation is 0.185 kg/m²/sec(3 d.p.). Meaning 2 litres of water with a surface area of 0.1m² and an air temperature above of 360C will evaporate dry in roughly 108 seconds.
This surely can not be right.
Can anyone advise on the errors of my ways?
Thank you in advance if you can.
 
Science news on Phys.org
UOP Student said:
Meaning 2 litres of water with a surface area of 0.1m² and an air temperature above of 360C will evaporate dry in roughly 108 seconds.
This surely can not be right.
"Surely" because of an observation, or "surely" because it just doesn't sound right? I would be surprised if water could hang around for too long so high above its boiling point. Unfortunately, my oven doesn't get that hot, so I can't test it. But perhaps I will see how long it takes for 2 L of water at 561 K (288 C) to boil away.
 
Surely in the sense that this time seems far too short a time for 2 litres of water to last. Air entering the vent system is 20 degrees and the air 250mm up is 360. That figure seems just too quick to me.
 
I was watching a Khan Academy video on entropy called: Reconciling thermodynamic and state definitions of entropy. So in the video it says: Let's say I have a container. And in that container, I have gas particles and they're bouncing around like gas particles tend to do, creating some pressure on the container of a certain volume. And let's say I have n particles. Now, each of these particles could be in x different states. Now, if each of them can be in x different states, how many total...
Thread 'Why work is PdV and not (P+dP)dV in an isothermal process?'
Let's say we have a cylinder of volume V1 with a frictionless movable piston and some gas trapped inside with pressure P1 and temperature T1. On top of the piston lay some small pebbles that add weight and essentially create the pressure P1. Also the system is inside a reservoir of water that keeps its temperature constant at T1. The system is in equilibrium at V1, P1, T1. Now let's say i put another very small pebble on top of the piston (0,00001kg) and after some seconds the system...
Back
Top