Three dielectric slabs in a capacitor

80 replies · 9K views · last reply
gracy said:
If dielectrics partition the space horizontally , they are in series and if dielectrics partition the space vertically then they are parallel. Correct?
And the direction of given capacitor plates is always considered to be horizontal. Right?
 
gracy said:
And the direction of given capacitor plates is always considered to be horizontal. Right?
Yes.
 
gracy said:
given capacitor plates
The plate which are at extreme positions i.e the left and right most.
 
gracy said:
The plate which are at extreme positions i.e the left and right most.
If the partition is parallel to the plates, they're in series and if the partition is perpendicular to the plates, they're in parallel.
 
  • Like
Likes   Reactions: gracy
cnh1995 said:
If the partition is parallel to the plates, they're in series and if the partition is perpendicular to the plates, they're in parallel.
Any exceptions?
 
gracy said:
Any exceptions?
None. But the partitions should be continuous from one end to the other.
 
Last edited:
cnh1995 said:
But the partions should be continuous from one end to the other.
You mean there should not be empty space in between ?
 
I meant something like this..
Diagram of a parallel-plate capacitor with two dielectric regions: K1 on the left half, K2 in the upper right, K3 in the lower right, separated by a dashed line; charges Q' and Q'' marked on the plates; width labelled d/2 on each side.
 
The two plates of parallel capacitors should have same area . Is that correct?
 
gracy said:
The two plates of parallel capacitors should have same area . Is that correct?
What do you mean by "two plates"? Which two plates?
 
http://astarmathsandphysics.com/university-physics/electricity-and-magnetism/parallel-plate-capacitors-html-9fd61e5.gif

Here the two plates have same area "A" ,I want to ask what if they had different areas , will they still form parallel plate capacitors together?
 
Last edited by a moderator:
gracy said:
http://astarmathsandphysics.com/university-physics/electricity-and-magnetism/parallel-plate-capacitors-html-9fd61e5.gif

Here the two plates have same area "A" ,I want to ask what if they had different areas , will they still form parallel plate capacitors together?
Yes. But the capacitance will be different.
 
Last edited by a moderator:
What will we write in place of A in the below formula ? A or B?
##\frac{Aε0}{d}## If one plate has area "A" and the other "B"
 
The charges have to be uniformly distributed on both the plates and the plates have different areas. I believe the capacitance calculation will be a little complicated.
 
Ok. What will be the formula of capacitance for the plate 2 here

Diagram of three parallel capacitor plates in series, numbered 1, 2 and 3, left to right. Plate 1 is light blue, plate 2 cyan, plate 3 teal. Terminals labelled 0 V on the left and Vp on the right, with potentials V1 and V2 marked between the plates.
 
What are those blue portions? Dielectrics? What are the red lines joining them? Wires?
 
cnh1995 said:
What are those blue portions? Dielectrics? What are the red lines joining them? Wires?
Yes and yes.
 
Given the area, separation and permitivitty, its capacitance would be C=Aε/d..
 
gracy said:
A is area of ? And why there isn't "K" present?
What's the need of k when there is 'ε' which is itself kεo? A is the area of each plate(which is same throughout). I don't understand why you are analyzing this diagram.
 
Ok. Fine. Let's end this thread here as it is going off topic.