Underwater data acquisition project

AI Thread Summary
The discussion revolves around a project focused on measuring load on a submerged chain in an underwater tank, requiring a hermetically sealed assembly for up to six months. The user has sourced IP68 load cells and a data logger but is seeking advice on enclosing a 24V power supply that can withstand underwater conditions. Suggestions include exploring dive shops for suitable underwater battery packs, although some users note that these may be too large for the project. There is also mention of a lithium polymer power source that meets IP68 standards, but its production status is uncertain. The conversation highlights the challenges of finding appropriate enclosures and power solutions for underwater electronics.
seanski06
Messages
3
Reaction score
0
I'm currently working on a project where I am required to measure the load that is applied to a chain, which is submersed in an underwater tank (approx. 20 feet). The entire assembly must be self contained and hermetically sealed for up to 6 months.

I've successfully sourced some good ip68 load cells and a datalogger, however I'm trying to figure out the best approach to enclosing a 24v power supply needed to power my sensors.

Does anyone have any experience working with electronics underwater? I can't seem to find much info on some good ip68 enclosures that will allow a cable port.

The most idealsolution would be a self contained 24v power supply that would consist of a box with two wires coming off of it.

Thanks for any help,
-Sean
 
Engineering news on Phys.org
Someone around these parts may have a better answer for you but have you tried looking in a dive shop to see what they have? I know they have big underwater battery packs for things like flashlights. Maybe you could use one of those.
 
seanski06 said:
I'm currently working on a project where I am required to measure the load that is applied to a chain, which is submersed in an underwater tank (approx. 20 feet). The entire assembly must be self contained and hermetically sealed for up to 6 months.

I've successfully sourced some good ip68 load cells and a datalogger, however I'm trying to figure out the best approach to enclosing a 24v power supply needed to power my sensors.

Does anyone have any experience working with electronics underwater? I can't seem to find much info on some good ip68 enclosures that will allow a cable port.

The most idealsolution would be a self contained 24v power supply that would consist of a box with two wires coming off of it.

Thanks for any help,
-Sean

Sean,

http://www.odi.com/" make the connections you seek.

CS
 
Last edited by a moderator:
Okefenokee: Most of those underwater battery packs are way too large for my application

Stewartcs: thanks for the info about ODI, I've been looking into what Seacon had, having more options is always a good thing

I found a really neat lithium polymer 14.8v dc source IP68 all the way...Unfortunately, the company has not decided to make them, I guess their just gauging interest
 

Thread 'How might electronics be different if AC voltage was 72V at 45 Hz?'

Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
View full post »

Thread 'Why does the amperage go real high if there is a low voltage short?'

I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
View full post »
Thread 'Electromagnet magnetic field issue'

Thread 'Electromagnet magnetic field issue'

Hi Guys We are a bunch a mechanical engineers trying to build a simple electromagnet. Our design is based on a very similar magnet. However, our version is about 10 times less magnetic and we are wondering why. Our coil has exactly same length, same number of layers and turns. What is possibly wrong? PIN and bracket are made of iron and are in electrical contact, exactly like the reference design. Any help will be appreciated. Thanks. edit: even same wire diameter and coil was wounded by a...
View full post »

Similar threads

TEG&Li+ batteries to power data collection sensors
Replies
1
Views
1K
Chemically regenerating my auto's catalytic converter?
Replies
19
Views
7K
Is Over-Engineering Hindering Your Success in Engineering Projects?
Replies
3
Views
12K
Do Movies Teach Us Realistic Life Skills?
Replies
1
Views
10K
Why is the U-2 nicknamed the Dragon Lady?
Replies
4
Views
8K

Hot Threads

Recent Insights

Back
Top