What is a CNC machine feed regulator?

  • Thread starter Thread starter Ctommy
  • Start date Start date
AI Thread Summary
A CNC machine feed regulator controls the feed rate of the machine, allowing adjustments to speed up or slow down the operation based on the programmed code. Users expressed frustration over insufficient images of the machine, which hindered understanding and discussion. There was a call for clearer, comprehensive pictures that include information labels to facilitate better communication. The thread was temporarily closed for moderation due to these ongoing issues. Clear visuals are essential for effective troubleshooting and discussion in CNC machine forums.
Ctommy
Messages
2
Reaction score
0
image.jpg
Does anyone know what this is?
 
Engineering news on Phys.org
This is CNC machine feed regulator.
At 100% the actual feedrate will be that in the code.
With the regulator, you can slow it down, or speed it up.
 
  • Like
Likes berkeman
Malverin said:
This is CNC machine feed regulator.
At 100% the actual feedrate will be that in the code.
With the regulator, you can slow it down, or speed it up.

Thank you so much. Do you know what these lights at the top are for?
image.jpg
 
I can not say what they are for from what I see here.
 
Ctommy

how long are you going to just mess us all around by showing us small section pics of some unknown much larger machine ??

your method is very frustrating to everyone
show a pic of the whole machine including its information labels !

else I will suggest to the mentors to lock this thread

Dave
 
Thread closed temporarily for Moderation...
 

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

What to Consider When Choosing a CNC Machine for Styrofoam Cutting?
Replies
2
Views
1K
CNC Machinist
Replies
4
Views
438
Home Solar Power Feed-in Tariff for Historical Domestic Installations in the UK
Replies
7
Views
1K
Controlling motor speed digitally
Replies
11
Views
1K
Efficient Voltage Conversion for High Amperage CNC Machines
Replies
1
Views
2K
How can I get my prototype made?
Replies
3
Views
1K
How does a voltage regulator differ from a zener diode?
Replies
38
Views
4K
Is this a good GM tube voltage regulator and rectifier?
Replies
18
Views
4K
Problem with different hydraulic connection sizes on CNC machines
Replies
2
Views
1K
What causes SWR to change along a feed line?
Replies
17
Views
5K

Hot Threads

Recent Insights

Back
Top