What is the acceleration due to gravity on the distant planet?

  • Thread starter Thread starter Physicsit
  • Start date Start date
AI Thread Summary
The discussion focuses on calculating the acceleration due to gravity on a distant planet using a hanging ball and a wire. An astronaut measures the time for a wave pulse to travel the wire and initially calculates gravity as 624 m/s², which is incorrect. After guidance, the astronaut recalculates using the correct formulas, arriving at a value of approximately 1.19 m/s² for gravity on the distant planet. The importance of retaining precision in calculations is emphasized to avoid discrepancies in results. The final calculation confirms that gravity on the distant planet is significantly lower than Earth's 9.8 m/s².
Physicsit
Can anyone verify my results below

To measure the acceleration due to gravity on a distant planet, an astronaut hangs a 0.085-kg ball from the end of a wire. The wire has a length of 1.5 m and a linear density of 3.1 ´ 10-4 kg/m. Us-ing electronic equipment, the astronaut measures the time for a transverse pulse to travel the length of the wire and obtains a value of 0.083 s. The mass of the wire is negligible compared to the mass of the ball. Recalling that the speed, v, of a small-amplitude wave on a string is given by
v=squareroot(F/(m/L))

mball= .085 kg
L= 1.5 m
m/L = 3.1 * 10^-4 kg/m (linear density)
t= 0.083 s
F=Tension=mg= (.085 kg)(9.8 m/s^2) F=.833 N

v=squareroot(.833(3.1*10-4) = 51.8 m/s

v= initial velocity + at

initial velocity=0

51.8 = 0 + a(.083)

51.8/.083 = a

acceleration= 624 m/s^2
 
Physics news on Phys.org
No.

In this situation, g is not 9.8 m/s^2.

9.8 m/s^2 is the acceleration due gravity near the surface of the earth. You are trying to find the equivalent quantity at the surface of that distant planet. The equation you are using, I would write as:

v = √(T/μ)

where v is the velocity of the wave, T is the tension in the wire, and μ is the mass per unit length of the wire. Note that T = mg in this situation is the weight of the ball only because the ball is suspended from, and therefore pulling down on, the wire. Since you are told that mass of the wire is negliglble, the weight of the ball is the only source of tension.

The weight of the ball THERE is mg. Therefore, g is the answer you are looking for. V, you are given (since you have been told the length of the wire and the amount of time it takes for the wave to traverse it).

Try again & see what you get.

PS: this equation:
v= initial velocity + at
has no applicability here at all. It applies to a moving object undergoing a constant rate of acceleration, such as an object in free fall, for example. (You understand that the ball is just hanging from the wire, not falling, don't you?)
 
Last edited:
Alright this should be it then

thank you for the guidance


does this look better


v=distance/time 18.07 m/s

18.07 m/s = ã(F/(m/L))

18.07= ã((m*g)/(m/L))

18.07 = ã((.083*g)/(3.1 * 10^-4))

((18.07^2)*(3.1 * 10^-4))/.083 = g

g =1.22 m/s^2
 
Close. I get 1.19 m/s2

The difference is that you used rounded intermediate results in your calculation.

If, instead, you rearrange the equations like this:
v = Δs/Δt
and
v = √(mg/μ)
Δs/Δt = √(mg/μ)
(Δs/Δt)2 = mg/μ
g = μ(Δs/Δt)2/m

Now enter the original amounts in your calculator:
g = 3.1x10-4(1.5/.083)2/.085
you'll get
g = 1.19...

It's better to hold off rounding until the end, or at least keep one or two extra decimal places in the intermediate results & then finish rounding at the end.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top