How to find the maximum rpm of the solid shaft that has a ring mounted on it?

AI Thread Summary
To determine the maximum RPM at which a ring mounted on a solid shaft with a 0.002" interference fit will remain secure, it is essential to consider factors such as thermal expansion and material properties. Running the shaft at 7000 RPM and 400 degrees Celsius raises concerns about the adequacy of the interference fit, especially if the shaft and ring are made from different materials. Differential thermal expansion could cause the ring to loosen, impacting its stability at high speeds. Calculating the thermal expansion and the forces acting on the ring at elevated temperatures will help assess whether the fit is sufficient. Understanding these dynamics is crucial for ensuring the ring remains securely attached during operation.
a.googoodolls
Messages
1
Reaction score
0
Hello,

I have to find the maximum rpm of the shaft that has ring mounted on the shaft with interference fit of 0.002". I want to know at what rpm the ring will come loose from the shaft?

and

If I run the shaft at 7000rpm at 400 degree Celsius, is the interference fit of 002" enough for the ring to hold on to the shaft? How can I find out if it is adequate or not?

Any suggestions will be appreciated.
 
Engineering news on Phys.org
Angular velocity will have no bearing on whether the collar will stay on the shaft. Differential thermal expansion could play a part though, if the two parts are made of different materials.
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Find 3D Printer & Software Resources for Prototype Creation'

I'd like to create a thread with links to 3-D Printer resources, including printers and software package suggestions. My motivations are selfish, as I have a 3-D printed project that I'm working on, and I'd like to buy a simple printer and use low cost software to make the first prototype. There are some previous threads about 3-D printing like this: https://www.physicsforums.com/threads/are-3d-printers-easy-to-use-yet.917489/ but none that address the overall topic (unless I've missed...
View full post »

Similar threads

Seeking ideas for how to achieve an adjustably damped shaft connector
Replies
6
Views
2K
How can I design a gear train to meet specific torque and RPM requirements?
Replies
2
Views
2K
Calculating Maximum Velocity Electric Longboard
Replies
8
Views
4K
Calculate Propeller RPM from Motor No Load RPM
Replies
2
Views
3K
Installing Snap Ring on a Shaft with Larger OD
Replies
4
Views
3K
Selection of gearbox for rotating a solid shaft
Replies
1
Views
1K
Calculating Maximum Force for C1018 Steel Shaft
Replies
9
Views
3K
How do I properly mount a needle bearing for a trike swing arm?
Replies
11
Views
3K
Stress in a ring that is mounted on a solid shaft
Replies
16
Views
9K
Plotting a Power Graph using Torque & RPM
Replies
3
Views
4K

Hot Threads

Recent Insights

Back
Top