A math or a simple fluid problem?

  • Thread starter Thread starter hanson
  • Start date Start date
  • Tags Tags
    Fluid
AI Thread Summary
The discussion revolves around solving a differential equation for the height of a tank over time, considering a constant inflow and a fluctuating component. The inflow is defined as a + bsin(wt), while the outflow is proportional to the square root of the height, represented as c*sqrt(H). There is uncertainty regarding the assumption of the outflow's relationship to height, with suggestions to revise this aspect. Additionally, a participant recommends expressing the radius in terms of height to simplify the equation. The overall consensus is that the problem is more mathematical than fluid dynamics.
hanson
Messages
312
Reaction score
0
Hi all!
I am solving for the height of a tank as a function of time.
The tank has a constant inflow of a and is subjected to small fluctuation of bsin(wt).
So the inflow is simply a+bsin(wt).
The outflow should be proportional to the square root of the height, H.
So outflow = c*sqrt(H)
Therefore the below differential equation is obtained with k=the area of the tank:
\frac{a+bsinwt-c\sqrt{H}}{k}=\frac{dH}{dt}


but the problem is that I don't know how to solve this ODE...
Can anyone solve the problem?
 
Engineering news on Phys.org
Have you been given this equation or have you set it up by yourself?
 
I set it up myself. And I have show my deduction:
The tank has a constant inflow of a and is subjected to small fluctuation of bsin(wt).
So the inflow is simply a+bsin(wt).
The outflow should be proportional to the square root of the height, H.
So outflow = c*sqrt(H)
Therefore the above differential appears.
Am i correct?
 
hanson said:
I set it up myself. And I have show my deduction:
The tank has a constant inflow of a and is subjected to small fluctuation of bsin(wt).
So the inflow is simply a+bsin(wt).
The outflow should be proportional to the square root of the height, H.
So outflow = c*sqrt(H)
Therefore the above differential appears.
Am i correct?

I am not sure about your assumption of the outflow. I would revise that.
 
this problem really has nothing to do with fluids..its just a math problem..

inflow is a+bsin(wt) correct.
outflow you said is proportional to square root of the height, h..
is then right too.. c*sqrt(h)...

now if you divide volume by cross sectional area you get height.. I am thinking you need to find the radius in terms of height also by rearranged the volume equation... that way your equation will be composed only of H terms.
 
I need some assistance with calculating hp requirements for moving a load. - The 4000lb load is resting on ball bearing rails so friction is effectively zero and will be covered by my added power contingencies. Load: 4000lbs Distance to travel: 10 meters. Time to Travel: 7.5 seconds Need to accelerate the load from a stop to a nominal speed then decelerate coming to a stop. My power delivery method will be a gearmotor driving a gear rack. - I suspect the pinion gear to be about 3-4in in...
Thread 'Calculate minimum RPM to self-balance a CMG on two legs'
Here is a photo of a rough drawing of my apparatus that I have built many times and works. I would like to have a formula to give me the RPM necessary for the gyroscope to balance itself on the two legs (screws). I asked Claude to give me a formula and it gave me the following: Let me calculate the required RPM foreffective stabilization. I'll use the principles of gyroscopicprecession and the moment of inertia. First, let's calculate the keyparameters: 1. Moment of inertia of...
Thread 'Turbocharging carbureted petrol 2 stroke engines'
Hi everyone, online I ve seen some images about 2 stroke carbureted turbo (motorcycle derivation engine). Now.. In the past in this forum some members spoke about turbocharging 2 stroke but not in sufficient detail. The intake and the exhaust are open at the same time and there are no valves like a 4 stroke. But if you search online you can find carbureted 2stroke turbo sled or the Am6 turbo. The question is: Is really possible turbocharge a 2 stroke carburated(NOT EFI)petrol engine and...

Similar threads

Replies
9
Views
2K
Replies
2
Views
1K
Replies
39
Views
12K
Replies
10
Views
2K
Replies
5
Views
3K
Replies
1
Views
1K
Back
Top