2 Questions of Momentum and Impulse

  • Thread starter Thread starter wolfpack
  • Start date Start date
  • Tags Tags
    Impulse Momentum
AI Thread Summary
The discussion centers on two physics problems involving momentum and impulse. For the first problem, the average force acting on a baseball hit back to the pitcher is calculated using the change in momentum and the contact time, leading to a revised force of approximately 2838.298 N after correcting for direction. The second problem involves a billiard ball collision, where the conservation of momentum is applied to find the velocity components of the first ball post-collision. Participants discuss the need for proper vector analysis and the use of trigonometric functions to resolve the angles involved. The conversation emphasizes the importance of correctly applying physics equations and understanding the direction of velocities in momentum calculations.
wolfpack
Messages
3
Reaction score
0

Homework Statement


Problem 1: A .145 kg baseball pitched at 40 m/s is hot on a horizontal line back to the pitcher at 52 m/s. If the contact time of the ball with the bat is 4.7e-3, calculate the magnitude of the average force acting on the ball due to the bat.

Problem 2:A billiard ball is moving at 3.1 m/s when it hits a stationary ball of the same mass. After the collision, the second ball moves at 2.4 m/s at an angle of 60.0 deg to the original line of motion, Find the magnitude and direction of the velocity of the first ball after the collision.

Homework Equations


Problem1) Impulse= change in momentum=m(v1-v2)=F((delta t))
Problem2)p=m*v


The Attempt at a Solution


My attempts at a solution are shown in the jpegs, with enumerated variables and equations I've tried. As for the method behind the madness, For problem one I am going off of the face that since impulse is the change is momentum, I can obtain a value from the quantifiable values for the momenta and then set the impulse equal to F delta t isolating the force in question.
For problem 2 I am going off of the conservation of momentum in a perfectly elastic collision. I know the enter of mass are uniform and masses are the same, and then I tried solving for the components of the momenta.
These questions are from the Andes OLI Learn by Doing series.
Thank you for your assistance
 

Attachments

  • linmomentum.JPG
    linmomentum.JPG
    55 KB · Views: 482
  • imp1.JPG
    imp1.JPG
    47 KB · Views: 457
Last edited:
Physics news on Phys.org
I can not follow your calculations, what have you got for the change of momentum in the first problem?

ehild
 
For the problem about impulse I have J=F (delta t)=delta p
F(t)=m(v2-v1)
F(4.7*10^-3)=.145(52-40)
Thus F=(.145(52-40))/(4.7*10^-3)=370.213 N
Apparently that is incorrect, but I am unsure of exactly what other equations to use with the quantities I have.

The change in momentum I got was (.145*52-.145*40)=1.74 (Kg*m)/s
 
wolfpack said:
For the problem about impulse I have J=F (delta t)=delta p
F(t)=m(v2-v1)
F(4.7*10^-3)=.145(52-40)

You forgot that the initial and final velocities have opposite directions. If v1 is positive, v2 is negative. Think it over.

ehild
 
Ah I see what I did now, so with the revised computation the correct solution is 2838.298 N which I checked and it works. Thank you

I still have that momentum equation left for my OLI, I'm just rusty on collisions in two dimension in general. I know the resultant angles have some connection to the component angles of the momenta, but I'm really just not sure where to proceed.
 
Find the velocity components parallel and normal to the original velocity. Apply sine and cosine of the given angle.

ehild
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top