Balancing Transformers: Info on Syncing, Load Balance & Power Loss

  • Thread starter Thread starter Sherman
  • Start date Start date
  • Tags Tags
    Transformers
AI Thread Summary
Balancing transformers are essential for synchronizing dual power sources, such as two generators, by matching their frequencies and distributing the load evenly. They help achieve better efficiency, particularly in three-phase systems, when each phase carries the same load in terms of current and reactance. While there is some power loss involved, users can still extract more power than the individual generators' output, as illustrated by the example of pulling 5.5 kW from two 3 kW generators. The discussion primarily focuses on single-phase applications, highlighting the need for more specific information in that area. Understanding these transformers is crucial for optimizing performance in setups with multiple power sources.
Sherman
Messages
2
Reaction score
0
Does anyone know where I can find information on Balancing Transformers.
A co-worker asked me about them, and I have not had much luck finding information on them. I do know that they are used when you have duel power sources, like two generators. The transformer syncs the frequencys and balances the load. I know that there is a little power loss. ex: (2) 3kW generators are hooked up to a balancing transformer, and you are able to pull 5.5 kW out of them.
 
Engineering news on Phys.org
You get the best efficiency from a, say 3-phase, transformer when each phase has the same load; both current and reactance.
 
Yes, but from my understanding, this is for use with single phase or three phase. I am mainly looking at the single phase application. Any ideals?
 

Thread 'Underwater piezoelectric sensor array receive sensitivity'

Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
View full post »

Thread 'Following up on the recent thread about Earth Resistance measurements'

I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
View full post »

Thread 'Question about bonding ground and neutral'

I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
View full post »

Similar threads

Ampere turn balance (MMF balance) in transformers
Replies
36
Views
12K
What's the normal low-load working temperature for an SMPS transformer?
Replies
27
Views
5K
Manually charging batteries
Replies
11
Views
2K
Balun Transformer vs. 180 Degree Hybrid Coupler?
Replies
10
Views
6K
How to Make a 24V Transformer Output 24V?
Replies
18
Views
4K
"Ground" and "Center Tapped" Power Transformer Secondary in guitar amp
Replies
6
Views
3K
Can power supplies/adapters be used to clean up dirty generator power?
2
Replies
61
Views
9K
Why reactive power is not tranferred between source and load
Replies
2
Views
1K
Relation between un-balanced loading and transformer loss
Replies
14
Views
13K
Calculating core losses in transformers
Replies
17
Views
7K

Hot Threads

Recent Insights

Back
Top