Balancing Work and Engineering Studies: Tips for Success

  • Thread starter Thread starter renjiLambrusc
  • Start date Start date
  • Tags Tags
    University
AI Thread Summary
Balancing work and engineering studies is feasible, especially with effective time management. Many students have successfully worked part-time jobs while maintaining good grades in demanding engineering programs. The choice between schools like UT and UTSA often hinges on personal connections and familiarity with the area. Maintaining a strong GPA is crucial for admission into competitive programs. Ultimately, with dedication and proper planning, it is possible to manage both work and academic responsibilities effectively.
renjiLambrusc
Messages
6
Reaction score
0
Hey guys,

i am getting ready to transfer to either UT or UTSA for EE next august, i was wondering if any of you guys ever worked or had a job while going to university. i will have to work to pay rent so i was wondering how hectic it is trying to work and get good grades in engineering. i will be working as a CAD designer so I'm assuming a part time position will be all i could do.

thanks.
 
Engineering news on Phys.org
Yes, I worked during college as well.

It will depend on you really and how much time you put toward your studies (vs. your social life). Engineering can be quite time demanding but if you allow a proper amount of time for homework and studying, you can certainly do it while working part time.

CS
 
Yes, I worked part time at Hewlett Packard, ~ 55 years ago, at $1.50 per hour. I was a "junior engineer" and built circuits using vacuum tubes, like a 420 MHz grounded-grid receiver.
Bob S
 
thanks guys, that's all i needed to know- if it was possible. if others have done it then i will try my best as well.
 
I can understand your dilemna, renjiLambrusc. I am actually about to start at SLCC, and then I will be transfering to ISU when I have completed my generals; and I will have to work full time while doing it.

Why are you deciding on UT, or UTSA? Just curious.
 
UT is close to where i am now and UTSA is my back up school. i have friends who graduated from Cockrell, in Austin, and they loved it there. plus, i used to live in Austin for seven years so i already know the area. as long as i keep my 3.6 gpa i should be able to get into the EE program at UT. i wouldn't mind going to UTSA or Texas State Univ. though. i just want a degree.
 
Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
Thread 'Weird near-field phenomenon I get in my EM simulation'
I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
Back
Top