Calculting the slope of the tangent to find Instantaneous velocity

AI Thread Summary
The discussion focuses on calculating instantaneous velocity using the slope of the tangent line on a position versus time graph for a pinewood derby car. Participants clarify that instantaneous velocity is defined as the limit of the change in position over time as the time interval approaches zero. To find this slope, one must draw a tangent line at a specific point on the graph and measure the rise over run, which can be simplified by creating a triangle from the tangent. There is also a correction regarding the calculation of average velocity for specific intervals. The conversation emphasizes the relationship between graphing and calculus in understanding motion.
FatIndian
Messages
2
Reaction score
0
EDIT: Ugh... I meant "calculating", of course.

This is an assignment that was due on the 16th. It's already been handed in, I just need some help with a question that I obviously was not able to answer in due time. I am coming back from a long, long hiatus from my academic pursuits and so some concepts that I had a firm grasp on in the past are now pretty fuzzy to me.

Homework Statement


P1. The position of a pinewood derby car was observed at various times; the results are summarized in the following table. Find the Average velocity of the car for (a) the first second, (b) the last 3s and (c) the entire period of observation.

t(s) 0-------1.0-------2.0-------3.0-------4.0-------5.0
x(m) 0-------2.3-------9.2-------20.7-------36.8-------57.5

P2. (a) Use the data in P1 to construct a smooth graph of position versus time. (b) By constructing tangents to the x(t) curve, find the instantaneous velocity of the car at several instants. (c) Plot the velocity versus time and, from this, determine the average acceleration of the car. (d) What was the initial velocity of the car?

Homework Equations


Average velocity: dx/dt
So P1 was easy enough:

(a) 2.30 m/s
(b) (57.5 - 9.20) / 3.00 = 16.1 m/s
(c) (57.5 - 0) / 5.00 = 11.5 m/s

P2:

(a) Constructing the graph was simple
(b) This is where I got stuck
(c) Couldn't calculate dv/dt because the previous part was incomplete

The Attempt at a Solution



So I know the instantaneous velocity corresponds to the limit of dx/dt as dt approaches zero, but I just didn't know how to go about doing that. The problem asks me to draw tangents and I did, I just didn't know how to derive the slope from that. I know the way to do this is pretty simple, but I'm just not getting it even after reading the relevant chapter several times.

Thanks in advance.
 
Physics news on Phys.org
Welcome to PF!

FatIndian said:
So I know the instantaneous velocity corresponds to the limit of dx/dt as dt approaches zero, but I just didn't know how to go about doing that. The problem asks me to draw tangents and I did, I just didn't know how to derive the slope from that. I know the way to do this is pretty simple, but I'm just not getting it even after reading the relevant chapter several times.

Hi FatIndian! Welcome to PF! :smile:

I think you're confusing two different things …

i] The instantaneous velocity is dx/dt.

ii] dx/dt is defined as the limit of {x(t + ∆t) - x(t)}/∆t as ∆t –> 0.

Forget ii]!

The velocity is dx/dt.

dx/dt is the slope of the tangent line.

The slope of the tangent line is the tangent of the angle that that line makes with the t-axis.

Any questions? :smile:
 
But how do I figure out at which point the tangent is hitting the t-axis?

Let's take t=5.0 as an example. The point is (5.0s, 57.5m). I know that when its tangent hits the t-axis, x=0, so all I have is (??s, 0m). I know I'm going about this the wrong way, I just can't figure out how.
 
FatIndian said:
But how do I figure out at which point the tangent is hitting the t-axis?

Let's take t=5.0 as an example. The point is (5.0s, 57.5m). I know that when its tangent hits the t-axis, x=0, so all I have is (??s, 0m). I know I'm going about this the wrong way, I just can't figure out how.

Hi FatIndian! :smile:

The question wants you to draw the curve, as smoothly as you can, and then draw the tangent at (5.0s, 57.5m).

You can draw it all the way to the t-axis if you like, or you can just draw enough of it to enable you to measure the slope.

But this is a drawing and measuring problem, not a calculating one. :smile:

(to calculate, you would need to use calculus … this is an introduction to how graphs and calculus are interrelated, and how you can use graphs instead of calculus. :wink:)
 
hey I had a similar question.
first I think you got wrong p1 b)
I think it suppose to be:57.5-20.7/5.0-3.0 which is 18.4..

second I am not sure myself how to find the instantenous velocity by drawing a tangent I think you need to crate a small triangle from the tangent then divide total y by total x and this is the instantenous velocity anyway I remmber I had troubles with this so I am not sure if any1 can explain better I would like to read thank you all
 
Hey Soulax! :wink:
Soulax said:
second I am not sure myself how to find the instantenous velocity by drawing a tangent I think you need to crate a small triangle from the tangent then divide total y by total x and this is the instantenous velocity

That's correct. :smile:

You can either draw a little triangle, or a great big one (usually as far as one of the axes) …

obviously, the larger the triangle, the easier it is to measure it! :biggrin:
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top