Charging a 3.7V 110mA Lithium Polymer Battery: Tips and Circuit Guide

AI Thread Summary
To charge a 3.7V, 110mA lithium polymer battery, it's essential to start with the battery's datasheet to understand its specifications and requirements. A suitable charging circuit can then be designed based on this information. Participants in the discussion emphasize the importance of knowing the make and model of the battery for accurate guidance. One user requests the datasheet, indicating difficulty in locating it. Proper charging practices are crucial for battery safety and longevity.
choyelise
Messages
4
Reaction score
0
Hi all!

I would like to know how to charge a lithium polymber battery of 3.7V, 110mA battery.
Anyone has the circuit ? Help!

Thank you!
 
Engineering news on Phys.org
Ideally this all starts with the datasheet for the battery, you then develop a circuit/system to "take care" of the battery.
 
@Windadct : Hi! Thanks for replying but do you have the datasheet because i couldn't find it.
 
You didn't say what the make and model of the battery is...
 
Model

Hi! @russ_watters here's the picture of the battery.
 

Attachments

  • IMG_2761[1].jpg
    IMG_2761[1].jpg
    47.4 KB · Views: 474

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Thread 'Question about the voltage between two charged capacitors'

suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
View full post »
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Similar threads

Battery protection circuit board
Replies
2
Views
1K
PM Generator and battery resistance
Replies
14
Views
2K
Safe to charge a Lithium Battery with a Voltage Limit?
Replies
2
Views
2K
Lemon Battery Voltage: Why More Resistance?
Replies
13
Views
3K
LED voltage indicator for 3.7v lithium ion battery
Replies
13
Views
9K
Voltage ratings of Li-Ion batteries
Replies
4
Views
3K
Battery circuit current flow when charging
Replies
19
Views
3K
Manually charging batteries
Replies
11
Views
2K
What Components Are Best for Designing a Lithium-Ion Charging Circuit?
Replies
2
Views
1K
Can a 12V DC Source Efficiently Charge a 16.9V Lithium Ion Battery Pack?
Replies
6
Views
2K

Hot Threads

Recent Insights

Back
Top