Find Replacement for LM1013 IC - Need Help

  • Thread starter Thread starter Engomar
  • Start date Start date
  • Tags Tags
    Amp Op amp
AI Thread Summary
The discussion focuses on finding a replacement for the LT1013 IC, initially confused with the LM1013. Users clarify that the LT1013 is available from Linear Technology for approximately $4.75, and it can be found online. There is also mention of the LT1013 being included in the free LTSpice program. Participants inquire about the specific requirements for a replacement, emphasizing the importance of matching parameters. Providing detailed specifications would facilitate finding a suitable alternative.
Engomar
Messages
2
Reaction score
0
please help me i need a replacement for lm1013 IC please does anybody have an idea ?
 
Engineering news on Phys.org
I've searched for LM1013 but I have not found any datasheet. Are you sure you got the part number correct?
 
Do you mean an LT 1013, which Maxim calls an LXM 1013?
 
yes sorry i meant LT 1013 and 2n4401 transistor please
 
Engomar said:
yes sorry i meant LT 1013 and 2n4401 transistor please

LT1013 is available, is there a reason why you want to replace it? If so, what is your requirement? It is impossible to match every parameters, but if you give the spec of what you need in the opamp, that would be much easier.
 

Thread 'Underwater piezoelectric sensor array receive sensitivity'

Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
View full post »

Thread 'Following up on the recent thread about Earth Resistance measurements'

I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
View full post »

Thread 'Question about bonding ground and neutral'

I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
View full post »

Similar threads

Op Amp with frequency compensation input
Replies
2
Views
1K
Importing SPICE models for some ICs into Multisim
Replies
6
Views
2K
Amplifier for piezoelectric sensor, OP Amp circuit
Replies
6
Views
5K
Composite signal generation IC in DIFAR Sonobuoys
Replies
11
Views
2K
Help for interpreting Opamps on a schematic
Replies
14
Views
3K
Need replacement advise for KA3525A IC
Replies
4
Views
4K
Op-amp compensation of cascade fudges audio signal oddly
Replies
3
Views
2K
Op-amp Oscillator Circuit Design (10-50 MHz)
Replies
6
Views
3K
Using delicate 5V IC to toggle 12V device with MOSFET, Diode, resistor
Replies
8
Views
1K
This op amp does not have gain?
Replies
4
Views
1K

Hot Threads

Recent Insights

Back
Top