How can I increase the pull-push force of my solenoid with specific parameters?

  • Thread starter Thread starter Davx1992
  • Start date Start date
  • Tags Tags
    Force Solenoid
AI Thread Summary
To increase the pull-push force of a solenoid, using a thicker wire (0.5 or 0.6 mm) and maximizing current to 1A is recommended. Calculations indicate that with 1000 turns and a length of 0.04m, the resulting force is approximately 0.021 Newton, which is insufficient for lifting heavier objects. To enhance the magnetic force, reducing the distance between the back iron plate and the bolt's end significantly increases the magnetic field strength. Incorporating iron components can help concentrate magnetic energy, thus improving the solenoid's performance.
Davx1992
Messages
3
Reaction score
0
Hello, I have some problems with my solenoid calculations. I have spent many hours, on searching for Formulas, and answers, but exact answer I cannot find. I made 2 electromagnets, and then tried with solenoids.
Last solenoid was made with 120 m long wire, 0,3 mm, center diameter was 12 mm and 4 cm long. I achieved 0,5 A on 12V. But solenoid pull force was weak.
So here is my question: My goal is to make solenoid which can push iron bolt (center) with neodymium magnet with push force similar with when put two permament magnets with same poles.
I planned max 1A and 12 V. How can I make solenoid with max force with such parameters, and what kind of wire I need- 0.3, 0.5, 0.6, 0.7, how long, Is it even possible, to gain such solenoid force, with such parameters.
Thanks.
And here is an image to show my idea.
009b85c.png
 
Engineering news on Phys.org
Hello Dave, :welcome:

Did you also try out your solenoid with the bolt inside?
 
Yeap, I made electromagnets with bolt inside. It was weak. I think problem is with wire, its too tight problably. And when I made my coil current was 0,5 A.
Now I think that i have to make solenoid with 0.5 or 0.6 mm wire, with 1A current, but I don't know how to calculate force, what I can reach and will it be enough for my project.
 
The ordinary pull force, for an iron bolt, can be estimated easily. The product of the current and the number of turns divided by the coil length gives the estimation of the magnetic field H inside the coil. The magnetic constant (1.26 microhenry/m) divided by 2 and multiplyed by the square of H gives the magnetic energy density inside the coil. Finally, the product of that energy density and the bolt cross section area gives the estimation of the magnetic pulling force (provided the end of the bolt is inside the coil).

As for pushing a permanent magnet, it's way more complicated, and the force must be much weaker...
 
Last edited:
Thanks for answer,
My calculations: 1000 turns Current: 1A , length 0,04m
H=25000
Then : (0.00000126/2) * 25000^2 = 393,75

Then: 393,75* 0.00005527000m² = 0,021 ??
Is it correct, and is it kg or lb?? What I calculated?
 
It's 0.021 Newton

https://en.wikipedia.org/wiki/Newton_(unit)

Your energy density is 393.75 joule/cubic_meter ; when you multiply it by 0.000055 square_meter , it gives 0.021 joule/meter - and joule/meter is exactly Newton, the SI unit for force.

0.021 Newton is the force you need to lift a 2.14 gram weight - not very much...

To increase the force, one should use additional iron things in order to concentrate the magnetic energy near the bolt end, like here:
s-l225.jpg
197-004-512E13B5.jpg

- the field H (not B ! ) is concentrated between the back iron plate and the internal end of the bolt (plunger). For example, it may be 4mm between them instead of your 40 mm - and then, the field is 10 times greater and the force is 100 times stronger.
 
Last edited:
  • Like
Likes Davx1992 and BvU
AlexCaledin said:
It's 0.021 Newton

https://en.wikipedia.org/wiki/Newton_(unit)

Your energy density is 393.75 joule/cubic_meter ; when you multiply it by 0.000055 square_meter , it gives 0.021 joule/meter - and joule/meter is exactly Newton, the SI unit for force.

0.021 Newton is the force you need to lift a 2.14 gram weight - not very much...

To increase the force, one should use additional iron things in order to concentrate the magnetic energy near the bolt end, like here:
View attachment 186520 View attachment 186521
- the field H (not B ! ) is concentrated between the back iron plate and the internal end of the bolt (plunger). For example, it may be 4mm between them instead of your 40 mm - and then, the field is 10 times greater and the force is 100 times stronger.
I'm building a coil to test a solenoid and your comments helped a lot. Would you mind plugging this last comment about the distance from the plunger end to the back iron plate into the formula you mentioned earlier? E.g: the solenoid is still 4cm long, but the bolt is almost reaching the end of it (just 4mm to reach it) how to use this info in the formula? Thanks in advance.
 
Back
Top