How do I convert mol/L to g/cm^3

  • Thread starter Thread starter alexisonsmith
  • Start date Start date
  • Tags Tags
    Convert
AI Thread Summary
To convert mol/L to g/cm^3 for refrigerant R134a, first determine its molecular weight, which is necessary for the conversion. The molecular weight of R134a is approximately 102.03 g/mol. Multiply the concentration in mol/L (5.0308 mol/L) by the molecular weight to obtain grams per liter. Then, convert grams per liter to grams per cm^3 by recognizing that 1 L equals 1000 cm^3. This process will yield the desired conversion from mol/L to g/cm^3.
alexisonsmith
Messages
28
Reaction score
0
How do I convert mol/L to g/cm^3 , I am wanting to know this for the refrigerant R134a from which the value I have is 5.0308 mol/L and I am wanting to convert it to g/cm^3

Thanks
 
Engineering news on Phys.org


You need molecular weight (mass per unit mole) for R134a. Multiply mol/L times mole weight to get grams/L then convert the liters to cm3.
 


ok, but I am having problems finding the mass per unit mole I think it is about 0.1050 Kg but I am not sure...
 

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'What type of toilet do I have?'

Thread 'What type of toilet do I have?'

I was enrolled in an online plumbing course at Stratford University. My plumbing textbook lists four types of residential toilets: 1# upflush toilets 2# pressure assisted toilets 3# gravity-fed, rim jet toilets and 4# gravity-fed, siphon-jet toilets. I know my toilet is not an upflush toilet because my toilet is not below the sewage line, and my toilet does not have a grinder and a pump next to it to propel waste upwards. I am about 99% sure that my toilet is not a pressure assisted...
View full post »

Thread 'Thread No-Go plug gage allows 3 turns to enter. That's too many!'

After over 25 years of engineering, designing and analyzing bolted joints, I just learned this little fact. According to ASME B1.2, Gages and Gaging for Unified Inch Screw Threads: "The no-go gage should not pass over more than three complete turns when inserted into the internal thread of the product. " 3 turns seems like way to much. I have some really critical nuts that are of standard geometry (5/8"-11 UNC 3B) and have about 4.5 threads when you account for the chamfers on either...
View full post »

Similar threads

Automotive Loss of gaseous volume because of fuel combustion
Replies
2
Views
1K
How to estimate enthalpy change across a compressor in simple vapor compression cycle
Replies
1
Views
207
Question in Thermal Physics (Van der Waals' Equation)
Replies
6
Views
2K
Convert J/mol k into atm cm^3/mol k
Replies
6
Views
7K
Chemistry Thermochemistry and the heat of complete combustion
Replies
4
Views
2K
Leakage of Air in a Spacecraft
Replies
16
Views
1K
Find temperature of a U-shaped Tube
Replies
9
Views
766
How to convert an inch dimension to arc minutes for precise measurement?
Replies
6
Views
2K
Predicting Remaining Pressure in Compressed Gas Cylinder
Replies
3
Views
3K
Automotive Can I convert a combustion engine car to a hybrid car?
Replies
4
Views
2K

Hot Threads

Recent Insights

Back
Top