How Long Does It Take for a Capacitor to Charge to 8V in an RC Circuit?

AI Thread Summary
The discussion focuses on calculating the time it takes for a capacitor to charge to 8V in an RC circuit with an 8500 Ω resistor and an 80 μF capacitor. The capacitive time constant was initially calculated as 0.65 seconds but was later corrected to 0.68 seconds for accuracy. Using the corrected time constant, the time required for the capacitor to reach 8V was recalculated to be 1.49 seconds. Participants emphasized the importance of maintaining precision in calculations to avoid round-off errors. The final answer for the charging time is confirmed as 1.49 seconds.
rlc
Messages
128
Reaction score
1

Homework Statement


A 8500 Ω resistor is joined in series with a 80 μF capacitor.
a) What is the capacitive time constant of this combination? (Solved: 0.65 s)
b) If a 9.0 volt battery is suddenly connected across this RC combination, how long will it take for the capacitor voltage to reach 8.0 volt?

Homework Equations


(amount for the capacitor with E-6)(ohms of resistor)=seconds
capacitor voltage= battery voltage (1-e^(-t/capacitive time constant))

The Attempt at a Solution

.[/B]
Part a: (amount for the capacitor with E-6)(ohms of resistor)=seconds
(80E-6)(8500)=0.65 sec

Part b: capacitor voltage= battery voltage (1-e^(-t/capacitive time constant))
8=9(1-e^(-t/rc))
0.889=1-e^(-t/rc)
-0.111=-e^(-t/rc)
0.111=e^(-t/rc)
ln(0.111)=ln(e^(-t/rc))
-2.1972=-t/rc
-t=(-2.1972)(rc)
...rc=0.65 s...
-t=(-2.1972)(0.65)
t=1.428 s

This is wrong. Please help me figure out where I am going wrong
 
Physics news on Phys.org
Your value for the time constant ##\tau## could be more accurate; 8 x 85 is not 650. Keep a few extra decimal places in intermediate values that will be used for further calculations. In fact, you'd be much better off using symbols only, not plugging in any values until the final step. I think you're losing accuracy by having round-off errors invade your significant figures.
 
  • Like
Likes rlc
Woops, you're right. My answer for the first part is actually 0.68 NOT 0.65.
Then, using 0.68 in that last calculation gives me 1.49 s, which is right. Thank you for catching that!
 
Thread 'Collision of a bullet on a rod-string system: query'
In this question, I have a question. I am NOT trying to solve it, but it is just a conceptual question. Consider the point on the rod, which connects the string and the rod. My question: just before and after the collision, is ANGULAR momentum CONSERVED about this point? Lets call the point which connects the string and rod as P. Why am I asking this? : it is clear from the scenario that the point of concern, which connects the string and the rod, moves in a circular path due to the string...
Thread 'A cylinder connected to a hanged mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...

Similar threads

Back
Top