Is E&M a Significant Part of a MechE Degree?

AI Thread Summary
E&M is not a significant focus in a Mechanical Engineering (MechE) degree, especially at institutions like Georgia Tech. Students typically only need to complete one required course in Physics 2, which covers E&M concepts. While E&M may seem irrelevant, there are conceptual and mathematical parallels between fluid dynamics and electromagnetics that could be beneficial. Experiences with E&M in high school may differ from college coursework. Overall, students can expect minimal emphasis on E&M in their MechE studies.
abcdegsds
Messages
2
Reaction score
0
How much E&M is involved in a MechE degree? I'm a high school senior in AP Physics C: E&M and I hate it with a passion. I loved Mechanics, but E&M is terrible. Would I just need to take the one required class (Physics 2), or do I need to use multiple E&M concepts throughout undergrad? I am going to Georgia Tech btw.
 
Engineering news on Phys.org
Virtually zero E&M is required or used; but keep in mind that classes/subjects can be very different between high-school and college---you might not feel the same way once you get there.
 
E&M may not be needed for ME, but there are many parallels between fluid dynamics and electromagnetics, - both conceptually and mathematically. Draw whatever conclusions you can from that fact.
 

Thread 'Race car suspension Class'

Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
View full post »

Thread 'Cantilever help'

I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
View full post »
Thread 'What's the most likely cause for this carbon seal crack?'

Thread 'What's the most likely cause for this carbon seal crack?'

We have a molded carbon graphite seal that is used in an inline axial piston, variable displacement hydraulic pump. One of our customers reported that, when using the “A” parts in the past, they only needed to replace them due to normal wear. However, after switching to our parts, the replacement cycle seems to be much shorter due to “broken” or “cracked” failures. This issue was identified after hydraulic fluid leakage was observed. According to their records, the same problem has occurred...
View full post »

Similar threads

Hardest content to learn for AP Physics C: Electricity & Magnetism
Replies
4
Views
4K
Does Electricity Need a Complete Circuit? Exploring Basic Physics Questions
Replies
6
Views
691
Intro Physics What Book Helps Understand Electromagnetism and Quantum Physics Concepts?
Replies
5
Views
4K
Admissions Advice on how best to spend my time for graduate school applications
Replies
15
Views
2K
Retired Engineer
Replies
1
Views
715
What sparked my passion for electrical engineering and physics?
Replies
1
Views
451
Plasma Physics: Stat Mech, Fluid Dynamics or Electrodynamics?
Replies
1
Views
2K
Programs Electrical Engineering vs. Robotics in Graduate School
Replies
7
Views
3K
Studying Advice on reading an entire physics textbook in one semester
Replies
20
Views
3K
Programs Can an Electrical Engineering Degree Lead to a Career in Astronomy?
Replies
13
Views
4K

Hot Threads

Recent Insights

Back
Top