Is a Small AC Generator Suitable for Running Electronics?

AI Thread Summary
A small 2.2kW AC generator is producing inconsistent power unsuitable for running electronics, as indicated by a buzzing noise from the PC power supply and failure of a UPS to charge. The generator likely outputs a modified sine wave rather than a pure sine wave, which can lead to operational glitches and potential power supply failure. True sine wave converters are available as a solution, but they may not be cost-effective for everyone. Users are advised to consider upgrading to a generator with inverter technology for better output quality. Overall, addressing the generator's output is essential for safely powering sensitive electronics.
gamefreak123
Messages
2
Reaction score
0
Hi all,
The country where I live, electricity outages are a part of life, so to compensate for it I have a small 2.2kW 220V AC generator in my house. The problem with it is that I've heard and found out for myself that its output is unfit for running electronics.

Testing with a voltmeter, the output is a consistent 220V, however, whenever I turn on my PC on it the power supply makes a weird buzzing noise. Also, I have a UPS w/ surge protector that doesn't even go on charge mode when plugged in with the generator on i.e. it doesn't consider the output suitable enough. Many laptop repairers and computer technicians have also warned me not to charge laptops from small, single phase generators.

So anyone have any idea what the problem might be, and more importantly any inexpensive way to get around it?

Thanks in advance.
 
Engineering news on Phys.org
Hi there "Gamefreak123"!
Your computer power supply wants a pure sine wave, and what it is probably getting is full of harmonics.

What model is your present generator, please?

Unfortunately, higher harmonics in the mains supplied to the computer can cause glitches in the operation of the machine, and can also cause power supply failure.
I have seen "true sine wave" converters, which produce nice clean mains power from 12V batteries.
Such converters are cheaper this year than they were last year. This link might help: http://www.powerstream.com/in15t.htm
 
*cough* some cheap Chinese one whose producer doesn't even have a website :D

Yeah you're probably right. I was hoping that there would be some magical device which could fine tune the generator's output and make it suitable, but I guess there isn't any. In that case, should I just buy a pair of fresh batteries for my old UPS? Its an http://www.ablerex.com.sg/downloads/products/tearsheet1000.pdf" a decent brand I think. You think its output would be good enough? It is pretty old.
 
Last edited by a moderator:
gamefreak123 said:
*cough* some cheap Chinese one whose producer doesn't even have a website :D

Yeah you're probably right. I was hoping that there would be some magical device which could fine tune the generator's output and make it suitable, but I guess there isn't any. In that case, should I just buy a pair of fresh batteries for my old UPS? Its an http://www.ablerex.com.sg/downloads/products/tearsheet1000.pdf" a decent brand I think. You think its output would be good enough? It is pretty old.

It's probably OK.
Although I cringe every time I see people use batteries.
 
Last edited by a moderator:
I noticed Honda has been producing small generators with inverter outputs. These have excellent output characteristics, but would probably be too wimpy for larger appliances.
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top