Reactive Power: A Strange Concept?

AI Thread Summary
The discussion critiques an article on reactive power, with one participant expressing that it offers no new insights, deeming it sophomoric and poorly reasoned. The concept of reactive power is debated, with some arguing it is an oxymoron and suggesting the term "power factor" is more appropriate. Utility operators are highlighted as the primary stakeholders concerned with reactive power, as it affects their operational efficiency and costs. Additionally, large electrical users are noted for their investment in systems to correct low power factors. The conversation emphasizes the ongoing relevance of the term "reactive power" in education and industry.
Eero
Messages
10
Reaction score
0
Hi!

What is your opinion about this article:

"www.bme.hu/ptee2000/papers/fetea.pdf"[/URL]
 
Last edited by a moderator:
Engineering news on Phys.org
Much ado about nothing. Everything he covered, I already learned in my sophomore year of college, majoring in EE. Seriously, very seldom do I read a paper and not get something out of it. I've been practicing EE for 32 yrs, and I'm less than a year away from my doctorate. Yet, I always learn something new, albeit just a small amount, when reading a paper like this one.

This paper, however, taught me absolutely nothing I didn't already know. In a nutshell, this paper is sophomoric claptrap, building and reducing straw men.

In general, anytime somebody claims that the status quo belief/teaching on a particular topic is "myth, misconception, etc.", and here is the "real" answer, 9 times out of 10, or actually 99 times out of 100, they are not as smart as they think they are. Also, their "answer" is usually just a trivial and narrow interpretation of narrowly selected laws, or the "misconceptions" they refute are just straw men. These people are not as smart as they believe. Also, those whom they refute are not as incapable as they believe.

I just lost 10 minutes of my life reading and critiquing what basically is a worthless article. This paper belongs in circular file no. 13. What a piece of rubbish.

Claude
 
Last edited:
I am on the same frequency as you !
 
Reactive power is an oxymoron, Where's the power? Use the term "power factor" instead. The only people who really care are the public utility power station operators, who see the extra current in their alternator stator windings because the power factor has not been corrected at the load.
Bob S
[added] The public utility has to provide a fixed amount of real power (kilowatts) to the user. If the user's power factor is low (meaning higher kVA), the utility has to provide more current to the user, which means more amps in the alternator, switch gear, and transmission lines, ultimately meaning more power loss and more water over the dam. So maybe reactive power is not an oxymoron in some cicumstances.
RS
 
Last edited:
Bob S said:
Reactive power is an oxymoron, Where's the power? Use the term "power factor" instead. The only people who really care are the public utility power station operators, who see the extra current in their alternator stator windings because the power factor has not been corrected at the load.
Bob S
Note that students will continue to see the term 'reactive power' though.

Also the large electrical users care about low power factors, as they invest in the corrective systems and pay the utilities for low power factor usage.
 
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top