Simple Magnet Question: Boost or Weaken Remotely

  • Thread starter Thread starter dyce
  • Start date Start date
  • Tags Tags
    Magnet
AI Thread Summary
Coiling wire around neodymium magnets can create electromagnetic effects, potentially allowing one magnet to influence another remotely. Spinning a reluctor in front of the first magnet may induce a change in the second magnet's strength, which could either increase or decrease based on the direction of the coil windings. The response may vary across the grid, depending on the precision of each coil's construction. The idea of using materials like mercury or metal filings to transmit a magnetic image is speculative and lacks clear evidence. Understanding these interactions is crucial for efficient grid development, making it important to research existing findings before investing time and resources.
dyce
Messages
17
Reaction score
0
new guy here with a simple question.

if i were to coil 10 turns of 14 gauge insulated wire around an 1/8" round x 1" long neodymium magnet, then wire it in parallel to a second magnet with 20 turns of the same gauge wire, what kind of change could i exspect in the second magnet if i spun a reluctor in front of the first magnet?

im trying to boost or weaken one magnet with another...remotely
 
Last edited:
Engineering news on Phys.org
to clarify my question and give you a motive i drew up a picture.

my question is when the reluctor wheel passes past one of one magnet what kind of response will i get in the other magnet?

-will there be an increase or decrease in the other magnets strength depending on the direction of the windings in the coils?

-will there be an equal response across the grid dependant on the accuracy of each coil of course?

-could a magnetic image somehow be broadcasted from one grid to the other through the use of mercury or metal filings?

these are just a couple of the questions i want answers to. in order to build a grid i need time and money. just want to know if the answers are already out there before i waste both.
 

Attachments

  • point.png
    point.png
    14.1 KB · Views: 409
Last edited:

Thread 'How might electronics be different if AC voltage was 72V at 45 Hz?'

Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
View full post »

Thread 'What happens if shielded cable has a short to the shield?'

While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
View full post »

Thread 'Why does the amperage go real high if there is a low voltage short?'

I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
View full post »

Similar threads

Replacing a remote with a switch -- voltage drop problems :(
Replies
2
Views
2K
Can Magnetic Induction Be Used to Boost or Weaken Magnets Remotely?
Replies
9
Views
4K
I How induction works within a coil (nuances of it)
Replies
6
Views
2K
Force of neodymium magnet inside an electromagnetic coil
Replies
1
Views
7K
Basics of RF coil development for MRI
Replies
11
Views
3K
Design & Build Electro-Magnet to Raise 1 KG weight
Replies
11
Views
11K
Alternator Inductor Coil Output Equation (?)
Replies
35
Views
19K
How many turns in my electromagnet?
Replies
1
Views
3K
Generator Design Questions (Electromagnetics)
Replies
1
Views
3K
Calculating the terminal velocity of a magnet falling through a copper coil
Replies
3
Views
2K

Hot Threads

Recent Insights

Back
Top