Solve Bernoulli's Problem: Water Flow in Garden Hose

  • Thread starter Thread starter jdg
  • Start date Start date
  • Tags Tags
    Bernoulli's
AI Thread Summary
A garden hose with a diameter of 13.5 mm experiences a significant reduction in flow area when stepped on, decreasing its diameter by a factor of 9. The initial water flow rate is calculated to be 8.59 m³/s. Using the Continuity Equation, the flow rate remains constant despite the change in diameter, leading to a calculated exit speed of 486 m/s after the hose is compressed. The discussion emphasizes that the flow rate before and after stepping on the hose must be equal, reinforcing the principle of mass continuity in fluid dynamics. This problem illustrates key concepts in fluid mechanics, particularly the relationship between area, velocity, and flow rate.
jdg
Messages
23
Reaction score
0
Next question: A garden hose with internal diameter of 13.5 mm lies flat on a sidewalk while water is flowing in it at a speed of 6 m/s. A person happens to step on it at the very edge of the opening of the hose and decreases its internal diameter by a factor of 9

So D (1) = 0.0135m
r (1) = 0.00675m
D (2) = 0.0135/9 = 0.0015m
r (2) = 0.00075m
A (1) = pi*r^2 = (3.14...)(0.00675^2) = 1.4134...e-4
A (2) = pi*r^2 = (3.14...)(0.00075^2) = 1.767...e-6

1. What was the water flow rate in the hose prior to the person stepping on it?
- I got this part: J(1) = A(1)V(1) = 8.59 m3/s

2. What is the flow rate of water after the person steps on it?

3. What is the speed of the water just as it exits the hose after the person steps on it?
 
Physics news on Phys.org
This actually is not a Bernoulli's equation problem.

Check your textbook (especially the section that I assume includes this problem) for something called a 'Continuity Equation'. Continuity of mass for an incompressible fluid says that the flow rate is a constant. That fact should be enough to get you through Parts 2 and 3.
 
Ok, for Q2, part 2 I did J = A(1)V(1) = A(2)V(2):

So V2 = V1*(A1/A2) = 486 m/s

Is this right?

And for part 3 I did

J = (A2)(V2) = 8.59e-4 m3/s
 
Flow rate = Av = constant.

Which means flow rate before the hose is stepped on = flow rate after the hose is stepped on.

Which means, if you are doing the problem correctly, what you are calling "J" should be the same bfore the hose is stepped on and after the hose is stepped on.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top