Very strange accidental proximity sensor - Explanation wanted

AI Thread Summary
An electronics project revealed an unusual behavior in an LED that lights up when a person approaches after being away for a while, with the duration of illumination proportional to the absence time. Two main theories were proposed: one suggests that the person becomes electrically charged, creating an electric field that activates the LED, while the other considers the possibility of a capacitive sensor that requires time to recharge. Additional anecdotes shared in the discussion highlight similar experiences with unexpected LED behavior due to proximity effects. The phenomenon appears to be linked to charge accumulation and conductivity changes in the environment. Overall, the discussion emphasizes the intriguing and often unpredictable nature of electronic components in response to human presence.
Ngineer
Messages
62
Reaction score
1
Hello everybody,

I was working on an electronics project, and one of the LEDs (actually I'm using only one) started acting really strange!

It will light up when I come close to it, ONLY if I have been out of the room for some time!

And that's not all, the period for which it will light up is proportional to how much I have been away (i.e. the longer I stay far from it the longer it will light when I return)


I was thinking of 2 possible explanations how this can happen,

Explanation 1. When I get out of the room I somehow get electrically charged, and this creates an E-field around the led when I return, making it conductive.
(But it will do this even if I go the other way (i.e. what matters is that I stay out of range, not where I go))

Explanation 2. The accidental sensor (be it capacitive or otherwise) is dependent on a capacitor that needs time to charge between "activations." But in this case it has a really wide range because I have to move 3~4 meters to get it to light again for a second or two!

Any input on this is appreciated, thanks!
 
Engineering news on Phys.org
I think there's a third explanation. Could it be that the LED is in love with you and the longer you are away the more it misses you?
 
No possible way to give you any advice on this unless we see a schematic.
 
This gives me a grin. This is a classic when using CMOS components. When I was but a wee lad, my boss showed me a machine that he could actuate / de-actuate by waving his hand. It had an open gate and was picking up charge from his proximity (assumable he was charged).
 
I had a similar event recently - something I could not explain but seems simpler than your situation.

I was working with a microcontroller and had an isolated LED/resistor tied to ground. If I came close to the anode of the LED, it would very slightly eluminated. I made sure that I was not touching any charged electronics.

More interestingly, if I firmly placed my feet on the ground then the LED would become dimmer. It seems that I was somehow conducting charge whilst sitting there.
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...

Similar threads

Back
Top