What is a Diffraction Limited Spot in Fluorescent Molecule Imaging?

  • Thread starter Thread starter Alice Jin
  • Start date Start date
  • Tags Tags
    Diffraction
AI Thread Summary
A diffraction limited spot in fluorescent molecule imaging refers to the smallest achievable spot size in an optical system with perfect focus and optics, represented by the Airy Disc. This concept is crucial for maximizing fluorescence signal collection, where a larger numerical aperture (NA) enhances signal capture, but ideally, the fluorescence should be concentrated on as few CCD pixels as possible to minimize readout noise. The relationship between numerical aperture and focal length is important, as they are interconnected in optical design. The physical size of the fluorescent molecule itself is distinct from the optical properties of the imaging system. Understanding these principles is essential for optimizing imaging performance in fluorescence microscopy.
Alice Jin
Messages
17
Reaction score
0
Dear everyone,

I'm wondering what the diffraction limited spot is.
When a laser(CW) is used to excite a fluorescent single molecule, the fluorescence from a single molecule is shown in the CCD camera. The size of fluorescence molecule is determined by Airy Disc which comes from diffraction limited spot. Is it right?
Does anyone explain this? Please~~ Thank you.
 
Science news on Phys.org
A diffraction limited spot is the best/smallest spot you can achieve with the system with perfect focus and perfect optics. Whether you can get this in real use depends on the system design/alignmnet.
It is often used for calcualtions of the limiting signal.
 
Thank you.
Then what's the factor to improve the limited spot I can see in terms of NA or focal lenth?
 
Not sure what you mean?
You want to collect as much of the fluorescence signal as possible, so assuming that the emission is uniform (it emits into a sphere) you want as large a numerical aperture as posible.
But then in signal-noise you want to put the spot onto as few CCD pixels as possible (ideally only one) because there is a readout noise associated with each pixel.
Which is where the diffraction limited bit comes in - for this you want a short focal length.

Unfortuantely Numerical Aperture and focal length are linked (for a given design of objective). Dependign on how weak the signal is and how much money you have - you might want to look at a schwarschild objective
 
Alice Jin said:
Dear everyone,

I'm wondering what the diffraction limited spot is.
When a laser(CW) is used to excite a fluorescent single molecule, the fluorescence from a single molecule is shown in the CCD camera. The size of fluorescence molecule is determined by Airy Disc which comes from diffraction limited spot. Is it right?
Does anyone explain this? Please~~ Thank you.

I think you are mixing concepts- the size of the fluorophore is not related to any optical properties of the system, it's a physical size of a molecule.

"diffraction limited" is taken to mean an aberration-free optical system. In this case, luminous points are imaged as Airy disks (YMMV- the assumption is that the aperture stop is rotationally symmetric and the optical system is linearly shift-invariant). The 'size' of the Airy function, which can also have several meanings, is usually taken to be similar to a full width half maximum and is given as 0.61*wavelength/(numerical aperture)

http://en.wikipedia.org/wiki/Airy_disc
 
Thread 'A quartet of epi-illumination methods'
Well, it took almost 20 years (!!!), but I finally obtained a set of epi-phase microscope objectives (Zeiss). The principles of epi-phase contrast is nearly identical to transillumination phase contrast, but the phase ring is a 1/8 wave retarder rather than a 1/4 wave retarder (because with epi-illumination, the light passes through the ring twice). This method was popular only for a very short period of time before epi-DIC (differential interference contrast) became widely available. So...
I am currently undertaking a research internship where I am modelling the heating of silicon wafers with a 515 nm femtosecond laser. In order to increase the absorption of the laser into the oxide layer on top of the wafer it was suggested we use gold nanoparticles. I was tasked with modelling the optical properties of a 5nm gold nanoparticle, in particular the absorption cross section, using COMSOL Multiphysics. My model seems to be getting correct values for the absorption coefficient and...
Back
Top