What is the future for photovoltaics?

  • Thread starter Thread starter Chaos' lil bro Order
  • Start date Start date
  • Tags Tags
    Future Photovoltaics
AI Thread Summary
The discussion centers on the current state and future of photovoltaic cells, highlighting that the most efficient silicon cells, particularly mono-crystalline, achieve efficiencies between 15% and 25%, with commercial averages around 18%. Photovoltaic cells primarily capture energy from the visible spectrum, with silicon effective up to about 1100 nm, but excess energy from higher-energy photons is often lost as heat. Research is increasingly focused on multi-junction cells and new materials to enhance efficiency and broaden the electromagnetic spectrum usage. Notably, lab tests have achieved over 40% efficiency, although such cells are not yet commercially available for general use. The conversation emphasizes the ongoing advancements in photovoltaic technology and its potential for future applications.
Chaos' lil bro Order
Messages
682
Reaction score
2
Yes, I was wondering if anyone was, perhaps familiar with the industry of photovoltaic cells and how that industry is maturing. In particular, how efficient are the best cells available today. I would guess its measured in something like Watts/Surface Area, or some statistic like that.

Another question I had was about how the cells capture EM energy. Do they collect a wide band of the EM spectrum, like say Gamma to Radio EM, or is it collecting mainly in say the visible 400-750nm spectrum, or mabye just a single wavelength?

Thank you in advance for good answers.
 
Engineering news on Phys.org
Hi, I'm sure you'll be able to get some better informed answers then what I'm about to say, however it might be enough to point you in the right direction for your own research. Anyway as far as I'm aware...

Currently the most common photovoltaic cells are Silicon in 3 forms - Amorophous, Multi-Crystaline and Mono-Crystaline. These have efficiencies ranging from 5% to 25% (worst case to best case) depending on the system, Mono crystaline being the most efficient, amorphous the least. The average for commercial use is about 18%.

A photovoltaic cell can generate electricity out of any photons with energy greater then the band gap. However I think that if a photon has energy greater then the band gap energy of the material, then this energy is generally lost as heat. If you google this paper , Shockley and Queisser, Journal of Applied Physics, March 1961, Volume 32, Issue 3. It has a good discussion of this subject, and a derivation of a maximum efficiency.

Most research is now focussing on developing Multi-junction Cells, as well as new compounds and organic dyes with photovoltaic properties. Multi-Junction cells have the advantage of making wider use of the EM spectrum.

I found this book really good. Clean Electricity from Photovoltaics, Mary Archer. ISBN 1-86094-161-3,

Hope that's some help.
 
Excellent reply Barny, just what I wanted. Thanks buddy, I shall enjoy reading your links.
 
No problem!
 
Silicon converts light up to about 1100 nm. It also converts down into the near-u.v., not sure of the exact cutoff wavelength there.

Solar radiation is roughly 1000 W/m^2, and Barny's efficiencies jive with what I've heard (around 15% for typical commercial devices, over 20% for "high-end" photovoltaics).

BTW, over 40% efficiency were achieved in the lab in Dec. 2006, but I've yet to hear of commercially available cells using the new technology.

I can't post URL's since I haven't made 15 posts here yet, but if you Google "Solar Cell Breaks the 40% Efficiency Barrier" (include the quotes) you'll get a link to an article about it.

The article also mentions 30% was achieved as early as 1994. These devices must be quite expensive, as they are used in satellites but you never hear of them being available to homeowners.
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top