Where can i find Aircraft Flight Data?

AI Thread Summary
Accessing actual flight data for aircraft performance can be challenging, but several resources may help. Aviation Week and Flight International provide detailed specifications, while libraries often have access to their publications. For real-time flight data, consider reaching out to organizations like NASA, DFLR, or ONERA, which may have recorded data from experimental flights. Additionally, contacting major airlines such as United or American could yield useful information, especially if the request is well-explained. Providing a clear rationale for the data's importance can enhance the chances of obtaining it.
earthgoodboy
Messages
3
Reaction score
0
Hi all

i am a student doing my thesis on the aircraft performance. However, i am in a need of actual flight data to validate my work. The parameters i am looking at are the range, fuel usage, velocity and altitude. Does anyone know where can i access to those data of any flights or any types of aircraft? The data could just be the average or the data of a single flight would be just fine.

Thank you
Anapat
 
Engineering news on Phys.org
The trade publication Aviation Week has pretty detailed specifications tables on their paywalled web site. These are also usually also in your library in a March issue.
Flight International has similar tables, perhaps a bit less comprehensive, in their annual World Airliner and World Military Aircraft Census issues. Again, check your library.

Do note that the parameters you list are all interdependent and that for normal use, the actual numbers will be well short of the extremes the type is capable of if one specific parameter, say range, is pursued.
 
Thanks you both for replying my post. but i think there is a bit misunderstanding here. The flight data I am looking for is actually the data recorded from a real flight, not the performance specification of the aircraft. It is sort of the data recorded every minute during the flight saying what is the current altitude, how far has been traveled and how much fuel left.

Btw, I am looking at particularly either turbo jet or turbofan engine.
 
What you are asking for is a raw data summary, which in reports is always adjusted to remove variance sources such as wind or temperature and atmospheric pressure differences.
You might get such data from NASA on some of their X planes, or perhaps ask some of the NASA counterparts in Europe like the DFLR or the ONERA in France. As a student, you might also get this kind of data from one of the domestic producers, such as Boeing. Ask for the data on some obsolescent type, maybe the 727 or the 717.
A big airline such as United or American would also have this kind of specifics and might be willing to let you have access. Please remember to ask nicely and to explain why this data is important to your studies. Just asking without a good rationale makes it harder for anyone to give you what you want.
 
Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'
Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Back
Top