[Worksheet] Horizontal/Vertical components + other

  • Thread starter Thread starter Torald
  • Start date Start date
  • Tags Tags
    Components
AI Thread Summary
The discussion revolves around a physics worksheet focusing on horizontal and vertical components of motion. The user struggles with applying trigonometry to calculate the horizontal and vertical components of velocity, initially miscalculating the values. After some guidance, they correctly determine the horizontal component (Hv) as 4.5 m/s and the vertical component (Vv) as 3.9 m/s, but express confusion about the sum of these components not equaling the total initial velocity. The conversation also addresses calculating the time it takes for an object to travel a horizontal distance and the vertical position of the object at that time, emphasizing the importance of considering gravity in the calculations. Overall, the user seeks clarity on how to approach the problems presented in the worksheet.
Torald
Messages
2
Reaction score
0
Hey there.

Was given this sheet a while ago. Went over it in class a week ago, completely forgot everything about it today (This is a fresh sheet, lost the one I did.). Have an NAB tomorrow, and couldn't find my physics teacher today to get this worked out.

So, the problem is that I have no clue with what to do. I got some basic info down, but that is it.

Course is in Higher Physics.


Thanks in advance.

Edit : FORGOT THE WORKSHEET!

Phys_001.jpg
 
Physics news on Phys.org
I don't understand what you wrote there.

For (a), you should consider a triangle, where one angle is 50° and the other one is 90° ("standing" on the ground). This will give a relation between horizontal speed and total speed, as well as a relation between vertical and total speed via trigonometry.

For b: Does the horizontal velocity change? If not, how can you calculate the time until the ball reaches the net?

c: What is the vertical position of the ball after that time?
 
Thanks for the reply.

U = Initial Velocity (6.0 m/s)

Hv = Horizontal Component (2.0m)

Vv = Vertical Component (0.9m)

Focusing on question a):

[STRIKE]Trigonometry...Egh. Hate it.

Since the Hv is perpendicular (90 degrees), to calculate the components, it would involve cos(x), right?
Don't know what do with that, though. For the Hv, would I do (As in, punt into a calculator) "6.0cos(90)"? Or "2.0cos(90)"? Or...?

As I said, I have not much of a clue as to what to do here.

Your help is most appreciated.

Edit: Alright. I think I figured out how to calculate the components.

Vv = 6sin(50) = 3.9

Hv = 6cos(50) = 4.5

But shouldn't they add up to 6? 3.9 + 4.5 = 8.4

Gah. Confuzzled.[/STRIKE]

Got it!

The Hv = Vcos(Θ)
= 6cos(50)
= 3.9

Trick to remember : HC - Horizontal Cos


The Vv = Vsine(Θ)
= 6sine(50)
= 4.5

Trick to remember : VS - Vertical Sine



For

D = 2.0
V = 6.0

So, use d=v/t |With rearranging| t = d/v

2.0/6.0 = 0.3



Although, I don't know what to do for [c]. Help would be good. I assume it involves the Vv, Velocity, time.
 
Last edited:
For c) so at 3 s it reaches the net. How far will it travel vertically in 3s with initial velocity 6sin30? If this is greater than 0.9 then it makes it over the net.
 
Torald said:
The Vv = Vsine(Θ)
= 6sine(50)
= 4.5
You should be careful with rounding (4.596...)

For

D = 2.0
V = 6.0

So, use d=v/t |With rearranging| t = d/v

2.0/6.0 = 0.3

No, it is a horizontal distance, and the horizontal speed is not 6m/s.


@ofeyrpf: Don't forget gravity.
 
TL;DR Summary: I came across this question from a Sri Lankan A-level textbook. Question - An ice cube with a length of 10 cm is immersed in water at 0 °C. An observer observes the ice cube from the water, and it seems to be 7.75 cm long. If the refractive index of water is 4/3, find the height of the ice cube immersed in the water. I could not understand how the apparent height of the ice cube in the water depends on the height of the ice cube immersed in the water. Does anyone have an...
Kindly see the attached pdf. My attempt to solve it, is in it. I'm wondering if my solution is right. My idea is this: At any point of time, the ball may be assumed to be at an incline which is at an angle of θ(kindly see both the pics in the pdf file). The value of θ will continuously change and so will the value of friction. I'm not able to figure out, why my solution is wrong, if it is wrong .
Back
Top