A (probably) simple RC circuit question

AI Thread Summary
To operate 12V solenoids with a periodic on/off cycle that ramps to full voltage, a simple RC circuit using a 555 timer and two BJTs is recommended. The first BJT can control the timing of the pulse, adjustable between 5-10 seconds, while the second BJT can manage the ramp-up time using a resistor and capacitor. The term "seated amps" refers to the steady state current draw when the solenoid is fully activated. The circuit can be designed to create a sawtooth waveform from a square wave for smoother operation. Resources for understanding 555 timers and BJTs are suggested for further education on building the circuit.
oldguy
Messages
3
Reaction score
0
Its been 30 years since my last Physics course so while I have the basic concepts I'm uncertain how to solve my current problem: I need to operate a pair of 12V solenoids (.5 seated amps, 4 watts each) with a periodic on/off cycle that gently ramps to full voltage (over about .5 to 1 sec) and then shuts off, repeating every 5-10 seconds (I'd love to be able to adjust this once my device is built and tested). It sounds like an RC circuit to me in theory but I'm lost as to how to proceed in reality at these voltage/amperage levels. I've looked into programmable controllers but this seems like over-kill for what strikes me as an essentially simple operation.

I'd love any help or thoughts on where to go to educte myself on this topic.

Thanks.
 
Engineering news on Phys.org
one 555 and a two bjts will do what you want, use one after the 555 (5-10 second adjustable pulse) with a drain resistor and cap that determines the rc time ramp of the base of the second bjt.
 
Last edited:
what is ".5 seated amps"
 
light_bulb: Thanks so much for the prompt response--it sounds like its very do-able but I'm strictly an amateur as far as real-world applications--would you mind taking a minute and breaking it down for me (or point me at a resource for understanding your response). don't know 555 or bjts and how do I figure out where to start to estimate values for resistor and capcitor. (sorry). thanks again.

and to moe_3_moe: seated amps refers to the steady state draw when the solenoid is fully activated and in the held state--
 
i made the circuit, should be adjustable from 3-15hz, and the ramp time also. didn't test it but i figure it's good for illustration. it is an astable circuit off the data sheet with a series resistor-cap off the discharge leg that is adjustable to turn the square wave into a slight saw. once again didn't test.
 

Attachments

  • Untitled-1.gif
    Untitled-1.gif
    6.5 KB · Views: 488
wow. thanks very much-that's phenomenally helpful. I'll dig in and see if I can put this together. I really appreciate your time.
 
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Thread 'Electromagnet magnetic field issue'
Hi Guys We are a bunch a mechanical engineers trying to build a simple electromagnet. Our design is based on a very similar magnet. However, our version is about 10 times less magnetic and we are wondering why. Our coil has exactly same length, same number of layers and turns. What is possibly wrong? PIN and bracket are made of iron and are in electrical contact, exactly like the reference design. Any help will be appreciated. Thanks. edit: even same wire diameter and coil was wounded by a...
Back
Top