A (probably) simple RC circuit question

AI Thread Summary
To operate 12V solenoids with a periodic on/off cycle that ramps to full voltage, a simple RC circuit using a 555 timer and two BJTs is recommended. The first BJT can control the timing of the pulse, adjustable between 5-10 seconds, while the second BJT can manage the ramp-up time using a resistor and capacitor. The term "seated amps" refers to the steady state current draw when the solenoid is fully activated. The circuit can be designed to create a sawtooth waveform from a square wave for smoother operation. Resources for understanding 555 timers and BJTs are suggested for further education on building the circuit.
oldguy
Messages
3
Reaction score
0
Its been 30 years since my last Physics course so while I have the basic concepts I'm uncertain how to solve my current problem: I need to operate a pair of 12V solenoids (.5 seated amps, 4 watts each) with a periodic on/off cycle that gently ramps to full voltage (over about .5 to 1 sec) and then shuts off, repeating every 5-10 seconds (I'd love to be able to adjust this once my device is built and tested). It sounds like an RC circuit to me in theory but I'm lost as to how to proceed in reality at these voltage/amperage levels. I've looked into programmable controllers but this seems like over-kill for what strikes me as an essentially simple operation.

I'd love any help or thoughts on where to go to educte myself on this topic.

Thanks.
 
Engineering news on Phys.org
one 555 and a two bjts will do what you want, use one after the 555 (5-10 second adjustable pulse) with a drain resistor and cap that determines the rc time ramp of the base of the second bjt.
 
Last edited:
what is ".5 seated amps"
 
light_bulb: Thanks so much for the prompt response--it sounds like its very do-able but I'm strictly an amateur as far as real-world applications--would you mind taking a minute and breaking it down for me (or point me at a resource for understanding your response). don't know 555 or bjts and how do I figure out where to start to estimate values for resistor and capcitor. (sorry). thanks again.

and to moe_3_moe: seated amps refers to the steady state draw when the solenoid is fully activated and in the held state--
 
i made the circuit, should be adjustable from 3-15hz, and the ramp time also. didn't test it but i figure it's good for illustration. it is an astable circuit off the data sheet with a series resistor-cap off the discharge leg that is adjustable to turn the square wave into a slight saw. once again didn't test.
 

Attachments

  • Untitled-1.gif
    Untitled-1.gif
    6.5 KB · Views: 486
wow. thanks very much-that's phenomenally helpful. I'll dig in and see if I can put this together. I really appreciate your time.
 
Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
suppose you have two capacitors with a 0.1 Farad value and 12 VDC rating. label these as A and B. label the terminals of each as 1 and 2. you also have a voltmeter with a 40 volt linear range for DC. you also have a 9 volt DC power supply fed by mains. you charge each capacitor to 9 volts with terminal 1 being - (negative) and terminal 2 being + (positive). you connect the voltmeter to terminal A2 and to terminal B1. does it read any voltage? can - of one capacitor discharge + of the...
Thread 'Weird near-field phenomenon I get in my EM simulation'
I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
Back
Top