(Acceleration) Car and Truck Problem

AI Thread Summary
The problem involves an automobile and a truck starting from rest, with the truck accelerating at 2.10 m/s² and the automobile at 3.4 m/s². The automobile overtakes the truck after the truck has traveled 50 meters. The time taken for the automobile to overtake the truck is calculated to be approximately 6.9 seconds. The initial distance behind the truck is determined to be about 30.94 meters. The calculations and reasoning provided appear to be correct.
XwyhyX
Messages
15
Reaction score
0
Here's the problem:

1. An automobile and a truck start from rest and at the same instant, with the automobile initially at some distance behind the truck. The truck has a constant acceleration of 2.10 m/s2, and the automobile an acceleration of 3.4 m/s2. The automobile overtakes the truck after the truck has moved 50.0 m. (a) How much time does it take the automobile to overtake the truck? (b) How far was the automobile behind the truck initially? (c) Draw the figure of the problem
2. Equations and Data : a=\frac{dV}{dt} ; V = \frac{dx}{dt}

CAR:
Acceleration = 3.4m/s2

TRUCK:
Acceleration = 2.10m/s2
Distance Traveled at time of overtaking = 50m
3. The Attempt at a Solution :
For a.)

Reading the problem, The time that the car overtook the truck should be the same as the overall time of the truck to cover 50m. So finding for t of the truck, I would have

\int2.10dt = \intdV

--Integrating this i would get

2.10t = V

I can solve for time using the equation for Velocity and 50 m as the displacement

V = \frac{dx}{dt}

\int2.10t dt=\int dx

--integrating this this

1.05t2 = x

-- substituting 50m to x

t2 = 50/1.05
t= 6.9 seconds

For b.)

Doing the same for finding the velocity of the truck above i would get

3.4t = V (for the car)

Also by computing

\int3.4t dt = \intdx

I would get

1.7t2 = x

Substituting 6.9 seconds would result to
x = 80.94 m

subtract this from 50m the

80.94 - 50 = 30.94m

Is this correct? Thanks in advanced :D
 
Physics news on Phys.org
Looks good to me!
 
Whew, I was having doubts with my solution. Thanks!
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top