Amplifying a He-Ne Laser: Tips and Guidelines for Beginners

  • Thread starter Thread starter HeNe
  • Start date Start date
  • Tags Tags
    Homework
AI Thread Summary
The discussion focuses on amplifying a He-Ne laser to increase its power for cutting applications, particularly in art and woodworking. The user expresses concerns about safety and knowledge gaps in laser amplification, seeking guidance on how to proceed. Suggestions include considering alternative laser types, such as CO2 or diode lasers, which are more efficient for cutting tasks. Additionally, resources like the alt.lasers Usenet group and Sam Goldwasser's website are recommended for further information and community support. Overall, the conversation emphasizes the challenges and considerations in enhancing laser capabilities for specific practical uses.
HeNe
Messages
5
Reaction score
0
This is not a homework

Hello
I am working on laser amplification(first time) for a He-Ne laser (160 cm ,80 watt)
But i don't know how to start the study because i am afraid of harming the device
I have so many ideas in my mind for example :
Making a q-switched laser ,or make anther laser and the pumping part of it is the He-Ne laser
i need to amplify it to reach 200 watt...
please any idea or where should i start

it is very important HELP
 
Physics news on Phys.org
Welcome to Physics Forums HeNe!

I've never heard of HeNe lasers at the power levels you are talking about. What is it you ultimately want to use the laser beam for? It might be better to use something other than a HeNe.
 
thank you for your welcome

i am working in cutting biz (plastic, wood) and i used a He-Ne laser

my main work is in art
and now i need to amplify the power of my laser so i can cut 1 deism of silver

i can't by any other device because i have so many loans on me [because of the sickens of my father]

and these is the main reason of trying to amplify the power of my laser...
and i have a Friend that told me about this website.. so i will try to remember my old physics courses
i am 55
and it is hard to remember every thing
 
From a quick internet search, I have the impression that C02 lasers are more common for woodcutting. It might be possible that diode lasers can also be used for this. As diode lasers are about the most efficient lasers available, they would be lower cost for a given power level.

There may be a few people here at Physics Forums who can give good advice on this, but I'll suggest you try asking at the usenet group alt.lasers :
http://groups.google.com/group/alt.lasers/topics
(You'll need either to create a google account -- it's free -- to post to alt.lasers, or have some other way to access usenet groups)

A number of regulars in alt.lasers build lasers as a hobby, and the "guru" of the group is Sam Goldwasser. His website has a little information on laser cutting with C02 lasers:
http://www.repairfaq.org/sam/laserco2.htm#co2mcwl
(Read the sections on "small wood cutting lasers" and "large wood cutting lasers")

You can also poke around on Sam's site wherever it mentions cutting and wood:
http://www.google.com/search?hl=en&safe=off&q=cutting+wood+site:repairfaq.org&btnG=Search

Good luck!

Mark

p.s. I am wondering if your setup uses the HeNe strictly as a visible alignment beam, and the real cutting is done by a C02 or other high-power laser?
 
I have recently been really interested in the derivation of Hamiltons Principle. On my research I found that with the term ##m \cdot \frac{d}{dt} (\frac{dr}{dt} \cdot \delta r) = 0## (1) one may derivate ##\delta \int (T - V) dt = 0## (2). The derivation itself I understood quiet good, but what I don't understand is where the equation (1) came from, because in my research it was just given and not derived from anywhere. Does anybody know where (1) comes from or why from it the...
Back
Top