Another RC circuit problem, don't understand why my answer is wrong

AI Thread Summary
The discussion revolves around solving an RC circuit problem involving a capacitor and two resistors after a switch is opened. The user initially misapplies the charging equation for the capacitor instead of using the correct discharging equation. The correct formula for the voltage across a discharging capacitor is V(t) = V0 * e^(-t/τ), where V0 is the initial voltage. After correcting the equation, the user finds the current through resistor R2 to be approximately 0.000445 A. The key takeaway is the importance of using the appropriate equations for charging versus discharging scenarios in RC circuits.
iiiiaann
Messages
22
Reaction score
0

Homework Statement


In the figure below, R1 = 13.0 kΩ, R2 = 18.0 kΩ, C = 0.600 µF, and the ideal battery has emf = 20.0 V. First, the switch is closed a long time so that the steady state is reached. Then the switch is opened at time t = 0. What is the current in resistor 2 at t = 4.00 ms?

27-55.gif


Homework Equations



V = IR

V_{Capacitor}(t) = V_{0}(1-e^{-t/\tau})

The Attempt at a Solution



Okay so i put a decent amount into this one but the answer I'm coming up with is wrong and I can't figure out why. Here's what I've done:

When the capacitor is fully charged, the current through the battery is \frac{\xi}{R_{1} + R_{2}} which is \frac{20}{13 * 10^{3} + 18 * 10^{3}} = 6.45e-4

The current through R2 would be the same as this, 6.45e-4, so the potential difference over R2 = IR = 6.45e-4 * 18e3 = 11.61 V

When the switch is first opened, the potential difference across the capacitor would be the same as this, 11.61.

The time constant for the capacitor would be RC = 18e3 * .6e-6 = 0.0108

so to calculate the potential difference at t = 4 ms, you would use the following equation:
V_{capacitor}(0.004) = 11.61 * (1 - e^{-0.004 / 0.0108}) which comes out to 3.59

This is the same as the potential difference in R2, and so current through R2 should be 3.59 / 18e3 = 1.99e-4, but that is not right. Can someone let me know where I went wrong?
 
Physics news on Phys.org
The potential across the capacitor will be falling, not rising. Check your equation for the potential on the capacitor!
 
This equation

\displaystyle V_\text{Capacitor}(t) = V_{0}(1-e^{-t/\tau})

is for the case of charging a capacitor which initially has a charge (and thus potential) of zero. How can I tell ? Look at V when t = 0 .

What's the correct equation for discharging a capacitor which initially has a potential of V0 across its plates?
 
is it just the same equation except without the "1 -" part? so V0(e^-t/TAU)?
 
got it, 0.000445358666. Thanks for putting me on the right track guys
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...

Similar threads

Back
Top