Bank Strong room (Vault) special HVAC requirements

  • Thread starter Thread starter tj00343
  • Start date Start date
  • Tags Tags
    Hvac
AI Thread Summary
Designing HVAC systems for bank vaults requires careful consideration of cooling and ventilation to protect sensitive items like documents and artwork. Consulting local building codes and ASHRAE guidelines is essential for compliance and best practices. Engaging with vault vendors can provide specific ventilation requirements tailored to their systems. It's crucial to avoid oversized ducts, which can lead to inefficiencies. Proper planning and professional expertise are vital for successful implementation of these specialized HVAC systems.
tj00343
Messages
59
Reaction score
0
Hey,
I'm designing the HVAC system for a bank.
What are the special cooling and ventilation requirements that go into the bank(specifically the vault ventilation) and where can i find resources regarding the subject.
Thanks in advance.
 
Engineering news on Phys.org
Sounds like a rather very specialised subject, which means this forum probably isn't the best place to ask.

Do they store fragile papers or artwork? In safe deposit boxes?
Perhaps ask the banks insurance company if they have any requirements?
I don't recommend large diameter ducts!
 
tj00343 said:
Hey,
I'm designing the HVAC system for a bank.
What are the special cooling and ventilation requirements that go into the bank(specifically the vault ventilation) and where can i find resources regarding the subject.
Thanks in advance.
Seems like for such a project, there should be some construction specifications lying around somewhere. I can't believe that someone has the gall to say "Build me a Bank. Let it be written; let it be done!" with no further thought.

As a first thought, consult local commercial building codes.

Second stop, consult with ASHRAE for any special guides or codes on the subject.

https://www.ashrae.org/

Third stop, vault construction is a specialized activity unto itself. You may need to discuss ventilation requirements with the vault vendor.
 
Limited experience here, but most regional/provincial/state/national jurisdictions specify the HVAC standards that must be conformed to. As Steamking mentioned. ASHRAE is very common. Furthermore, there are aspects of the design that are left up to the designer/engineer in which case experience from a competent professional is required.
 
CWatters said:
I don't recommend large diameter ducts!

That's terrible advice. All vault systems must be sized to allow access to Tom Cruise.

BoB

PS: extra credit for novel use of lasers.
 
  • Like
Likes russ_watters

Thread 'Bubble formation in 4 mm gap vessel'

How did you find PF?: Via Google search Hi, I have a vessel I 3D printed to investigate single bubble rise. The vessel has a 4 mm gap separated by acrylic panels. This is essentially my viewing chamber where I can record the bubble motion. The vessel is open to atmosphere. The bubble generation mechanism is composed of a syringe pump and glass capillary tube (Internal Diameter of 0.45 mm). I connect a 1/4” air line hose from the syringe to the capillary The bubble is formed at the tip...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Find 3D Printer & Software Resources for Prototype Creation'

I'd like to create a thread with links to 3-D Printer resources, including printers and software package suggestions. My motivations are selfish, as I have a 3-D printed project that I'm working on, and I'd like to buy a simple printer and use low cost software to make the first prototype. There are some previous threads about 3-D printing like this: https://www.physicsforums.com/threads/are-3d-printers-easy-to-use-yet.917489/ but none that address the overall topic (unless I've missed...
View full post »

Similar threads

Lab Ventilation Energy Use and COVID
Replies
5
Views
1K
Underground pump vault airflow considerations
Replies
15
Views
3K
How can adjacent air be accounted for in fresh air exchanges for HVAC systems?
Replies
4
Views
2K
Calculating Exhuast Flow for Fume hoods and BSC
Replies
1
Views
1K
Laboratory HVAC Design Inquiries
Replies
2
Views
1K
Where can I find resources for becoming an HVAC engineer?
Replies
4
Views
5K
IEC 60890 - Heat Rise Calculations
Replies
8
Views
6K
Determining the required properties of a submersion cooler system
Replies
1
Views
1K
Shivering with the thermostat set to 75 F HVAC question
Replies
21
Views
8K
Pressure loss in an HVAC system
Replies
19
Views
3K

Hot Threads

Recent Insights

Back
Top