Calculating Acceleration in a Pulley System

AI Thread Summary
In a pulley system involving an 80 kg man and a 40 kg dumbwaiter, the acceleration was calculated to be 0.2 m/s² downward. The man exerts a force of 200 N, which affects the system's dynamics. Initial calculations by users varied, with one suggesting an acceleration of 8.1 m/s², but this was incorrect. The correct approach involves analyzing forces separately, leading to the conclusion that the net force results in a downward acceleration. The final answer aligns with the textbook solution, confirming the acceleration of the dumbwaiter.
eno
Messages
7
Reaction score
0
PLZ HELP! I am puzzled with this problem, and all i could find are that the forces equal, but the ans int eh back of the textbook clearly says the solution is 0.2 m/s2

Question: This situation occurs in a pulley system. A 80.0 kg man inside a 40.0 kg dumb waiter (like an elevator) pulls down on the rope. At the end of the rope, it is attached to the dumb-waiter. At the other end, the person exerts a force. At that moment, the scale on which he is standing reads 200N. Determine the elevator's acceleration.

THX for ur time!
 
Physics news on Phys.org
Hmm.. that's wierd. I didn't get 0.2m/s^2

Let me try to understand this better. The man is inside the dumbwaiter (which will pull up the elevator) has a mass of 80kg, the dumbwaiter is 40kg, so total mass of the dumbwaiter is 120kg. Correct?


http://img52.exs.cx/img52/1381/2035.gif


I got 8.1 m/s^2 as an answer. So I don't know if I'm wrong, or the book is.
 
Last edited:
MAYBE this is the correct answer:
80+40=120

(120)(9.8)=1176

F=MA

A=\frac{F}{M}

A=\frac{200}{1176}

A=0.17m/s^2
Probably the 0.17 is rounded off.
 
Last edited:
sorry, Raza, nice try. the 1176 is the force, and not the mass, so u cannot use the force of 200N to divide that force, which results in some unknown unit number. THe answer just conincidently matches with the ans int he book, but i am sure the way u got it is wrong...again, thanks for trying.

physik, here's the link to the actual question and diagram from the textbk:

http://www.enovon.com/public/physics.jpg

again, thanks for trying, maybe u can understand the problem better by this clear picture :)
 
Last edited by a moderator:
Let us consider the dumb-waiter separately.
The man standing on it has a mass 80 kg, but the force exerted by him on the elevator is 200N.
He is applying some force on the rope, say F.
80g-F=200
You can solve this to know F.
Now the weight of the elevator is 40 kg ang the force exerted by the man is 200N. Let the acc. of the elevator be a.
F-200-40g=40a.
Substituting F=80g-200
we get 80g-200-200-40g=40a
Therefore,40g-400=40a
Therefore,a=g-10,
Therefore,a=-0.2m/s^2
That is 0.2 m/s^2 downwards
 
thx alot, gauravkukreja!
 
Thread 'Voltmeter readings for this circuit with switches'
TL;DR Summary: I would like to know the voltmeter readings on the two resistors separately in the picture in the following cases , When one of the keys is closed When both of them are opened (Knowing that the battery has negligible internal resistance) My thoughts for the first case , one of them must be 12 volt while the other is 0 The second case we'll I think both voltmeter readings should be 12 volt since they are both parallel to the battery and they involve the key within what the...
Thread 'Correct statement about a reservoir with an outlet pipe'
The answer to this question is statements (ii) and (iv) are correct. (i) This is FALSE because the speed of water in the tap is greater than speed at the water surface (ii) I don't even understand this statement. What does the "seal" part have to do with water flowing out? Won't the water still flow out through the tap until the tank is empty whether the reservoir is sealed or not? (iii) In my opinion, this statement would be correct. Increasing the gravitational potential energy of the...
Back
Top