Can I desgn a rotating disc without using a centre shaft

AI Thread Summary
It is feasible to design a rotating disc with a central hole without using a center shaft by employing a rim that connects to the disc's interior or exterior, allowing it to slide through a supporting structure. For horizontal spinning, three or more rollers can support the disc's rim, with some rollers driven to create rotation. A design proposal includes multiple layers spinning in opposite directions, raising questions about the placement of the driver for optimal functionality. The use of a large planetary gear is also suggested, prompting inquiries about suspending the gears in mid-air for rotation. Overall, innovative mechanisms can support and drive a disc without a central shaft.
jeredane
Messages
3
Reaction score
0
Is it possbile to spin a disc that has a hole in the centre like normal DVDs but without using a rotating centre shaft that is passing through the hole?

The spining disc has to be supported too by a structure. Is there any mechanism to recommend?
 
Engineering news on Phys.org
Yes, it is possible. There are a number of ways to do this, but it all comes down to a rim attached to either the inside of the hole or the outside of the wheel. This rim slides through the supporting structure.

Some practical examples, demonstrated on bicycle wheels:
http://www.designboom.com/weblog/cat/8/view/11207/hubless-spokeless-bicycle-wheel-compilation.html
 
Last edited by a moderator:
Hey.. THanks for the reply!

How about if the disc is being spin horizontally? is there anyway of supporting the disc without the centre shaft?
 
Three or more rollers around the rim with one or more driven to provide spin.
 
The following picture is a ride that i have design. the outer and the inner layers spin in the same direction and the middle layer spin in the opposite direction. how can i spin the outer layer of the ride and the middle layer of the ride? where can i place the driver?

If i were to use a planetary gear that is very big is it possible? Is there anyway to supend the gears in mid air and let it rotate?
 

Attachments

  • Ride.jpg
    Ride.jpg
    20.6 KB · Views: 491

Thread 'Race car suspension Class'

Posted June 2024 - 15 years after starting this class. I have learned a whole lot. To get to the short course on making your stock car, late model, hobby stock E-mod handle, look at the index below. Read all posts on Roll Center, Jacking effect and Why does car drive straight to the wall when I gas it? Also read You really have two race cars. This will cover 90% of problems you have. Simply put, the car pushes going in and is loose coming out. You do not have enuff downforce on the right...
View full post »
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'

Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
View full post »

Thread 'Cantilever help'

I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
View full post »

Similar threads

Using a motor to spin two discs in opposite directions
Replies
6
Views
820
How can I connect a 6mm motor shaft to a 15mm disc shaft?
Replies
1
Views
2K
I Motional EMF in Faraday disc, co-rotating magnet axial mean flux
Replies
5
Views
99
Can you help me calculate the required torque and power of this motor?
Replies
8
Views
3K
Torque calculations: Rotating vertical shaft
Replies
5
Views
5K
I Can a permeable but non-magnetic rotor be used in an electric motor?
Replies
18
Views
1K
Faraday disc voltage increase
Replies
3
Views
1K
Shear Stress between Two Rotating Discs
Replies
5
Views
5K
I Charge movement relative to magnetic field frame dependence/invariance
Replies
5
Views
862
Control the rotation of several discs along the same axis
Replies
1
Views
1K

Hot Threads

Recent Insights

Back
Top