Connect Multiple Devices with One Switch: An Electronics Question

  • Thread starter Thread starter Jelfish
  • Start date Start date
  • Tags Tags
    Multiple Switches
AI Thread Summary
The discussion revolves around connecting multiple devices to a single signal source using a switch. The original poster sought a solution for switching between two devices without needing individual switches for each pin. Suggestions included using a 50 Ohm splitter if the devices and source matched in impedance, but more information about the signal type was needed for precise advice. Ultimately, the poster found they no longer needed the solution but expressed interest in a rotary switch for future use. Participants mentioned that pre-made switching boxes for various I/O ports are available online and at local electronics stores.
Jelfish
Messages
147
Reaction score
5
I'm not very experienced with electronics so this might be a simple question:

I have a tool that outputs signal information through a serial cable. I have two devices that connect with it, so I physically pull the plug and switch connections when needed. However, I would like to create a box with all three things connected and switch between the destinations with one switch. However, since there are several pins in use, I'm not sure how to do this without actually using a switch for each pin. Is there an easy way to do this? I would prefer to not have to power this switch also.

Thanks!
 
Engineering news on Phys.org
The answer depends on a number of things. Can you post more info (datasheets?) about the signal source and the two devices that monitor the signal?

Like, if the source and destinations are all 50 Ohms, then you can use a 50 Ohms splitter with a known loss to split the signals, and then just adjust your gain at the two receiving ends to account for the constant loss.

Is the data flow all one way, with no return information? Is the signal digital or analog? What is the bandwidth?

You have lots of options, we just need more info in order to be of help.
 
Thanks berkeman.

It turns out that I don't need this anymore. However, what I was looking for was something like a rotary switch, specifically a 6-pole 2-position.

Thanks anyway :)
 
Jelfish said:
Thanks berkeman.

It turns out that I don't need this anymore. However, what I was looking for was something like a rotary switch, specifically a 6-pole 2-position.

Thanks anyway :)
You can get a box all made up with connectors and and appropriate switching for almosts any I/O port for a few dollars.
 
NoTime said:
You can get a box all made up with connectors and and appropriate switching for almosts any I/O port for a few dollars.
Really? Are you referring to a particular store or somewhere online? This may be useful in the future. Perhaps I should ask the local electronics shop.
 
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
Thread 'Beauty of old electrical and measuring things, etc.'
Even as a kid, I saw beauty in old devices. That made me want to understand how they worked. I had lots of old things that I keep and now reviving. Old things need to work to see the beauty. Here's what I've done so far. Two views of the gadgets shelves and my small work space: Here's a close up look at the meters, gauges and other measuring things: This is what I think of as surface-mount electrical components and wiring. The components are very old and shows how...
Back
Top