Connecting two rollers together

  • Thread starter Thread starter thoain14
  • Start date Start date
AI Thread Summary
To connect two conveyor rollers that are 2 ft apart, options include using a metal shaft or a torque tube, but care must be taken to avoid using a thin rod that could fail under torque. The rollers should be aligned correctly, and the bearings need to be positioned at the outer ends, not the inner ones. Alternative solutions include using stepped pulleys and belts to transfer motion or employing an electrical approach with a servo motor driven by a shaft encoder. The need for a connection depends on whether one roller drives the other and the specific torque requirements. Providing detailed dimensions and torque needs will help refine the best connection method.
thoain14
Messages
8
Reaction score
0
Hi there,
I have two conveyor rollers that are on the same plane about 2 ft apart. How can I connect their axles together while keeping that 2 ft distance? I was thinking of just getting a metal shaft and welding it together
 
Engineering news on Phys.org
Welcome to PF.

Are the rollers on the same axis ?
Free running conveyor rollers usually have a fixed shaft with bearings at each end to support the roller.
How are your rollers arranged?
Do they have internal bearings or are the bearings attached to the support frame.
 
Yes the rollers are on the same axis. I need to line them up side by side. The bearings will be at the outer ends of both rollers but not the inner ones. I need to somehow connect the two rollers together. From the top view, the order or parts will be Frame, Bearing, Roller, Something that connects the two, Roller, Bearing, Frame.
 
Replace the two rollers with a single length of the same size tube, to make one long roller. Keep the end bearings from one of the original rollers.

thoain14 said:
Yes the rollers are on the same axis. I need to line them up side by side.
That seems to contradict itself. Side by side on the same axis, or end to end ?
Post a diagram or drawing of the roller positions and the bearing assembly.
 
1637686389639.png

It would be something along the lines of this. I did not want to use one roller because it would be so long. I was wondering if I was able to not use a bearing on the inside ends and figure out a way to connect them.
 
The simplest way to transfer torque between the two rollers is with a large diameter, thin wall, “torque tube”. When transferring torque, the material nearest the neutral axis is not helpful.

Your picture shows only a thin rod, which has only the material closest to the neutral axis. That is exactly the wrong way to do it. A thin rod would be a twist or torque spring and could easily fail. The rollers will need to slip against the belt to protect the connection rod from damage.

There are many other mechanical solutions. For example a stepped pulley on each roller, connected by a stepped belt, that passes around diagonal rollers, to turn the belt through 90° at each end.

There are also electrical solutions. For example, you could mount a shaft-encoder on the master roller, then drive the other roller with a servo motor as the slave.

Why do you need a connection?
Does the connection drive one of the belts from the other?
How much torque do you need to transfer between the rollers?
What are the length, diameter, and separation dimensions of the rollers?
 
Thread 'Physics of Stretch: What pressure does a band apply on a cylinder?'
Scenario 1 (figure 1) A continuous loop of elastic material is stretched around two metal bars. The top bar is attached to a load cell that reads force. The lower bar can be moved downwards to stretch the elastic material. The lower bar is moved downwards until the two bars are 1190mm apart, stretching the elastic material. The bars are 5mm thick, so the total internal loop length is 1200mm (1190mm + 5mm + 5mm). At this level of stretch, the load cell reads 45N tensile force. Key numbers...
I'm trying to decide what size and type of galvanized steel I need for 2 cantilever extensions. The cantilever is 5 ft. The space between the two cantilever arms is a 17 ft Gap the center 7 ft of the 17 ft Gap we'll need to Bear approximately 17,000 lb spread evenly from the front of the cantilever to the back of the cantilever over 5 ft. I will put support beams across these cantilever arms to support the load evenly
Back
Top