Creating Realistic Fireflies for Production of 'As You Like It

  • Thread starter Thread starter lightnb
  • Start date Start date
  • Tags Tags
    Electronic
AI Thread Summary
Creating a realistic firefly effect for 'As You Like It' involves using LEDs with a dominant wavelength of 570 nanometers, mimicking their natural pulsing behavior. The recommended method includes utilizing two 555 IC Timer chips to control the flicker and on/off cycles, with specific resistor and capacitor values to achieve the desired timing. A sawtooth wave generator can also be employed to create a quick on and slow decay effect, allowing for a more realistic fade-out. For variable timing, a PIC microcontroller may be a better option. Expert solutions are available for those seeking advanced firefly reproductions for various applications.
lightnb
Messages
1
Reaction score
0
I am the Lighting Designer for a production of 'As You Like It' and have been asked to find a way to create a realistic firefly effect.

From my research, Fireflys have a dominant wavelength of 570 nanometers. They fade on quickly, pulse (a very fast fade on and off) at a rate between 2.5 and 3.5 Hz (varying from firefly to firefly), and then fade out. The on cycle should last between 1.5 and 3 seconds, and the off cycle should be 4 to 7 seconds.

They make LEDs with a dominant wavelength of 570 nanometers and I was considering using (2) 555 IC Timer chips, one to control the flicker within the on cycle, and one to control the on and off cycle itself.

My question is, is this the most effective way to achieve this effect? If not, what would you recommend?

If so, how can I make the pulses fast-fade instead of blink? How do I determine the values of the resistors and capacitors to get the desired rates? And finally, how do I get the 'firefly' to fade out at the end of it's on cycle instead of blinking off?

I would greatly appreciate any insight you could offer on this project.

Thanks,

Nick
 
Engineering news on Phys.org
Try looking up sawtooth wave generator.
So called because the output waveform resemble the teeth of a saw.
If set up properly it will produce a quick on with slow decay to off.

If you set up a 555 to produce narrow pulses, then you can charge a capacitor with the pulse. The decay to 0 time is dependent on the value of the cap and resistance of the led. Set the cap/led to decay in your 1.5 to three seconds and the repetition time of the 555 to be your 4 to 7 seconds.

If you want variable times, like sometimes 4 and sometimes 7 sec and/or decay times then i would look into using a PIC (a small single chip computer)
 
This post is probably too late for your production. However, we are the leader in the design & manufacture of realistic firefly reproductions for stage, screen, zoos, natural history museums, commercial locations, and home backyards. We even design units that Universities utilize to lure-in real fireflies for research.

Through the use of our patented microprocessor technology and accurate LED selections we can mimic virtually any of hundreds of species of firefly from around the world. We are alway happy to discuss the specific needs of any project in order to determine if our 'Firefly Magic' fireflies will work. http://www.ledsfx.com"
 
Last edited by a moderator:
Hey guys. I have a question related to electricity and alternating current. Say an alien fictional society developed electricity, and settled on a standard like 73V AC current at 46 Hz. How would appliances be designed, and what impact would the lower frequency and voltage have on transformers, wiring, TVs, computers, LEDs, motors, and heating, assuming the laws of physics and technology are the same as on Earth?
While I was rolling out a shielded cable, a though came to my mind - what happens to the current flow in the cable if there came a short between the wire and the shield in both ends of the cable? For simplicity, lets assume a 1-wire copper wire wrapped in an aluminum shield. The wire and the shield has the same cross section area. There are insulating material between them, and in both ends there is a short between them. My first thought, the total resistance of the cable would be reduced...
I used to be an HVAC technician. One time I had a service call in which there was no power to the thermostat. The thermostat did not have power because the fuse in the air handler was blown. The fuse in the air handler was blown because there was a low voltage short. The rubber coating on one of the thermostat wires was chewed off by a rodent. The exposed metal in the thermostat wire was touching the metal cabinet of the air handler. This was a low voltage short. This low voltage...
Back
Top