How can I create a simple latch mechanism using a roller chain for my project?

AI Thread Summary
A user is designing a latch mechanism using a roller chain and sprockets to lift and drop an object along a vertical slider rail. The setup involves a motor-driven sprocket and an idler sprocket, with a #40 roller chain facilitating the movement. Suggestions include using a U-shaped pin attached to a chain link to effectively engage and release the object, ensuring it can slide off during the cycle. The user confirmed that the design is feasible and thanked contributors for their assistance. The discussion highlights the importance of simple mechanical solutions without additional motors or electronics.
HowardF
Messages
2
Reaction score
0
I'm looking for a simple latch design. My project will have two roller chain sprockets positioned one above the other with about a two foot gap. A motor will turn one of the sprockets and the other is just an idler sprocket. A #40 roller chain will run around the two sprockets. Mounted just beside this chain and sprocket setup, will be a vertical slider rail with an object that travels up and down the rail.

I need something attached to a chain link(s) that will circle the bottom sprocket, latch onto the object on the slider rail, drag/lift the object upwards, then release(drop) the object before, at, or while the chain link carries around the top sprocket. The latch mechanism must then again latch the object next time around the bottom sprocket and repeat the latch/lift/drop cycle indefinitely.

I am looking for a simple design without incorporating additional motors or electronics if possible. I can add additional levers/pulleys or anything necessary. Please let me know. Thanks so much!
 
Engineering news on Phys.org
HowardF said:
I'm looking for a simple latch design. My project will have two roller chain sprockets positioned one above the other with about a two foot gap. A motor will turn one of the sprockets and the other is just an idler sprocket. A #40 roller chain will run around the two sprockets. Mounted just beside this chain and sprocket setup, will be a vertical slider rail with an object that travels up and down the rail.

I need something attached to a chain link(s) that will circle the bottom sprocket, latch onto the object on the slider rail, drag/lift the object upwards, then release(drop) the object before, at, or while the chain link carries around the top sprocket. The latch mechanism must then again latch the object next time around the bottom sprocket and repeat the latch/lift/drop cycle indefinitely.

I am looking for a simple design without incorporating additional motors or electronics if possible. I can add additional levers/pulleys or anything necessary. Please let me know. Thanks so much!

Welcome to the PF.

How heavy is the object to be lifted, and how big is it? Do you really need a latch, or could it just be a cup to pick up and drop off the object?

Do you have any conceptual drawings yet? I looked around Google Images some, but didn't have quite the right search terms yet. Perhaps you will have better luck...

http://www.technicopedia.com/8835/8835cforks.jpg
8835cforks.jpg
 
If you replace one of the roller pins with a longer pin, an object with two slightly curved arms can catch on the long pin and be raised until it reaches the top sprocket when the roller chain pin will move away and so disengage from the arms.
If the object falls down the rail quickly you can use two long pins, equally spaced in the one chain, to double the rate of lift and drop.
 
I have attached a picture as per Berkeman's suggestion. The weight could be as much as 10 lbs. I'm hoping a single link on a chain has that much strength, otherwise I use a more robust chain.

Baluncore,
I have thought of just that. However, if I'm understanding you properly, the problem is when the link travels around the upper sprocket, the pin won't "slide" away horizontally to disengage from the curved arms. The pin will remain at 90 degrees to the chain link and will follow the sprocket so it will travel up and point vertical then continue traveling down and point horizontal again pointing in the other direction, thereby hooking onto an not releasing the curved arm..
However, that gave me an idea. I have a special chain link which contains a small bracket. If I attach a U shaped pin to the link, as in my 2nd diagram, the arm on the slider will slide off the U shaped pin nicely I think.

Oh wait, if you meant the curved arms to be curved vertically, then yes you are 100% correct as the pin will slide along the curved surface until it's released, same as what I drew only the switch the pin onto the chain and the curved bracket onto the sliding piece.

Yes, this is solved...thanks so VERY MUCH! Greatly appreciated!
Chain & Sprocket Diagram.jpg
Chain & Sprocket Diagram 2.jpg
 
Here's a video by “driving 4 answers” who seems to me to be well versed on the details of Internal Combustion engines. The video does cover something that's a bit shrouded in 'conspiracy theory', and he touches on that, but of course for phys.org, I'm only interested in the actual science involved. He analyzes the claim of achieving 100 mpg with a 427 cubic inch V8 1970 Ford Galaxy in 1977. Only the fuel supply system was modified. I was surprised that he feels the claim could have been...
TL;DR Summary: Heard in the news about using sonar to locate the sub Hello : After the sinking of the ship near the Greek shores , carrying of alot of people , there was another accident that include 5 tourists and a submarine visiting the titanic , which went missing Some technical notes captured my attention, that there us few sonar devices are hearing sounds repeated every 30 seconds , but they are not able to locate the source Is it possible that the sound waves are reflecting from...
Thread 'Turbocharging carbureted petrol 2 stroke engines'
Hi everyone, online I ve seen some images about 2 stroke carbureted turbo (motorcycle derivation engine). Now.. In the past in this forum some members spoke about turbocharging 2 stroke but not in sufficient detail. The intake and the exhaust are open at the same time and there are no valves like a 4 stroke. But if you search online you can find carbureted 2stroke turbo sled or the Am6 turbo. The question is: Is really possible turbocharge a 2 stroke carburated(NOT EFI)petrol engine and...
Back
Top