How can I create an active noise control stereo using simple terms?

  • Thread starter Thread starter T.O.E Dream
  • Start date Start date
  • Tags Tags
    Control Noise
AI Thread Summary
Creating an active noise control stereo involves using speakers to cancel out unwanted sounds, similar to how noise-canceling headphones work. Proper placement of the noise source, noise-canceling speakers, and listeners is crucial for effective sound cancellation. Understanding sound properties, such as the speed of sound and frequency ranges, can help in designing the system. Additionally, speakers reproduce different instruments' tones by tracing distinct waveforms, allowing listeners to recognize each instrument's unique sound. Effective implementation requires a grasp of these fundamental concepts in acoustics and speaker technology.
T.O.E Dream
Messages
219
Reaction score
0
I want to create an active noise stereo which works like the headphones except it's a big speaker. I need your help on how i would go about doing this? I ain't no electrical engineer or anything, in fact I have no knowledge whatsoever so try to help me using simple terms.
 
Engineering news on Phys.org
T.O.E Dream said:
I want to create an active noise stereo which works like the headphones except it's a big speaker. I need your help on how i would go about doing this? I ain't no electrical engineer or anything, in fact I have no knowledge whatsoever so try to help me using simple terms.

Have you been through the intro page at wikipedia, and followed some of the links at the end of the article?

http://en.wikipedia.org/wiki/Active_noise_cancellation

.
 
A question about active noise control. Does there need to be a specific angle at which the speakers must be at with the sound source?
 
T.O.E Dream said:
A question about active noise control. Does there need to be a specific angle at which the speakers must be at with the sound source?

Yes, I believe that placement of both the noise source, the noise cancelling speaker(s) and the listener(s) are important. Can you tell us why that would be? BTW, do you know the speed of sound in air? And what is the normal range of frequencies of audio sounds that we hear? What are the corresponding wavelengths of sound in air? (Quiz questions for you)
 
im a musician who is also studying physics at high school, and we have come to the part where we talk about how speakers work and so on, but what i asked and my teacher couldn't sanswer was, how does a speaker produce the different tone colours of instruments.
if a violin plays a concert C and then a trumpet plays a concert C, how does the speaker change the tone of the sound so we recognise it as the respective instrument??
 
A good quality speaker will just reproduce the waveform that comes from the instrument.

Because the waveforms are different from each other, our ears recognise the instrument by its different waveform.

This is the waveform of a saxaphone:
http://hyperphysics.phy-astr.gsu.edu/HBASE/Music/saxw.html#c3
saxw1.gif


This is the waveform of a clarinet
http://hyperphysics.phy-astr.gsu.edu/hbase/Music/clarw.html
claw1.gif


Note that the speaker cone can only be in one position at a time, so it only traces one waveform, even if it is reproducing all the instruments of the orchestra.
 

Attachments

  • saxw1.gif
    saxw1.gif
    4 KB · Views: 475
Hi all I have some confusion about piezoelectrical sensors combination. If i have three acoustic piezoelectrical sensors (with same receive sensitivity in dB ref V/1uPa) placed at specific distance, these sensors receive acoustic signal from a sound source placed at far field distance (Plane Wave) and from broadside. I receive output of these sensors through individual preamplifiers, add them through hardware like summer circuit adder or in software after digitization and in this way got an...
I have recently moved into a new (rather ancient) house and had a few trips of my Residual Current breaker. I dug out my old Socket tester which tell me the three pins are correct. But then the Red warning light tells me my socket(s) fail the loop test. I never had this before but my last house had an overhead supply with no Earth from the company. The tester said "get this checked" and the man said the (high but not ridiculous) earth resistance was acceptable. I stuck a new copper earth...
I am not an electrical engineering student, but a lowly apprentice electrician. I learn both on the job and also take classes for my apprenticeship. I recently wired my first transformer and I understand that the neutral and ground are bonded together in the transformer or in the service. What I don't understand is, if the neutral is a current carrying conductor, which is then bonded to the ground conductor, why does current only flow back to its source and not on the ground path...
Back
Top