How can I find 4 channel oscilloscope in multisim 11

AI Thread Summary
To find a 4-channel oscilloscope in Multisim 11.0, users must have the 'pro power' suite, as the 'base' or 'full' suites only support 2-channel oscilloscopes. There is no formal way to add a 4-channel oscilloscope in the lower-tier suites. For those needing multiple waveforms quickly, alternatives like PSpice or LTSpice IV are recommended, with LTSpice being free and capable of displaying numerous waveforms. Users can refer to National Instruments for a comparison of the different Multisim suites. Overall, upgrading to the 'pro power' suite is necessary for accessing a 4-channel oscilloscope in Multisim.
ultraxp
Messages
5
Reaction score
0
Hi, how can I find 4 channel oscilloscope in multisim 11.0? or how can I add 4 channel oscilloscope to multisim?
 
Engineering news on Phys.org
It depends on which suite you have installed. If you have the 'base' or 'full' suite, then your are limited to a 2 channel oscilloscope. For a 4 channel oscilloscope, you must have the 'pro power' suite. Check the following link from National Instruments to compare between the different Multisim suites:

http://www.ni.com/white-paper/5733/en

I would recommend using PSpice if you are in real hurry. You can display as many waveforms as you like in simulation.
 
Is there any options to have 4 channel oscilloscope?
 
No, there's no a formal way to have a 4 channel oscilloscope other than in the 'pro power' suite. If you can substitute Multisim, then use LTSpice IV. It's free and capable of displaying as many waveforms as you like. Get it from the link:

http://www.linear.com/designtools/software/#LTspice
 
thanks for replies :)
 
Thread 'Weird near-field phenomenon I get in my EM simulation'

Thread 'Weird near-field phenomenon I get in my EM simulation'

I recently made a basic simulation of wire antennas and I am not sure if the near field in my simulation is modeled correctly. One of the things that worry me is the fact that sometimes I see in my simulation "movements" in the near field that seems to be faster than the speed of wave propagation I defined (the speed of light in the simulation). Specifically I see "nodes" of low amplitude in the E field that are quickly "emitted" from the antenna and then slow down as they approach the far...
View full post »

Thread '3-terminal device external modeling'

Very basic question. Consider a 3-terminal device with terminals say A,B,C. Kirchhoff Current Law (KCL) and Kirchhoff Voltage Law (KVL) establish two relationships between the 3 currents entering the terminals and the 3 terminal's voltage pairs respectively. So we have 2 equations in 6 unknowns. To proceed further we need two more (independent) equations in order to solve the circuit the 3-terminal device is connected to (basically one treats such a device as an unbalanced two-port...
View full post »

Similar threads

Tektronix 2465A change rear signal output
Replies
7
Views
1K
How to estimate the measurement uncertainty of an oscilloscope ?
Replies
6
Views
3K
Using Tektronix Oscilloscope to Measure Phase
Replies
10
Views
5K
Understanding Multisim Simulation Results: Schematic and Oscilloscope Analysis
Replies
9
Views
3K
Questions for Electronics Engineering Experts: Oscilloscope, Function Gen & DMM
Replies
1
Views
1K
Tektronix 2465 Oscilloscope problem
Replies
9
Views
5K
Can't trigger on 2 channels simultaneously on oscilloscope =/
Replies
8
Views
14K
Troubleshooting a High Frequency Mixer: Oscilloscope Output Analysis
Replies
24
Views
6K
Unwanted noise in oscilloscope diaplay
Replies
12
Views
2K
How to measure output voltage of B200?
Replies
3
Views
2K

Hot Threads

Recent Insights

Back
Top