How Do You Calculate Motion and Forces in Physics Problems?

AI Thread Summary
To calculate motion and forces in physics problems, it's essential to apply principles of equilibrium and energy conservation. For the solid sphere rolling down the incline, the speed at the bottom can be derived using gravitational potential energy and rotational kinetic energy equations. In the case of the suspended boom, analyzing the forces and creating a free body diagram (FBD) will help determine the tension in the horizontal cable. Similarly, for the plank, establishing equilibrium conditions and drawing the relevant diagrams is crucial for calculating the tension in the cable. Providing attempts or progress is necessary for further assistance in solving these problems.
katiegerster
Messages
13
Reaction score
0
physics circular motion and gravity help please :(

1. a) A solid homogeneous sphere of mass M = 4.80 kg is released from rest at the top of an incline of height H=1.35 m and rolls without slipping to the bottom. The ramp is at an angle of θ = 25.7o to the horizontal. Calculate the speed of the sphere's CM at the bottom of the incline.

b) Determine the rotational kinetic energy of the sphere at the bottom of the incline.

2. A mass M=169 kg is suspended from the end of a uniform boom.The boom (mass=90.0 kg, length=3.60 m) is at an angle θ=68.0 deg from the vertical, and is supported at its mid-point by a horizontal cable and by a pivot at its base. Calculate the tension in the horizontal cable.

3. A plank of length L=1.800 m and mass M=7.00 kg is suspended horizontally by a thin cable at one end and to a pivot on a wall at the other end.The cable is attached at a height H=1.50 m above the pivot and the plank's CM is located a distance d=0.700 m from the pivot. Calculate the tension in the cable.
 
Physics news on Phys.org
First show us the attempt.
 
i actually just figured out question one
but i don't even know how to start 2 and 3 :(
 
To start the second one. First draw the Diagram. Then draw the FBD. Show it to us. Same applies for the third one.

Drawing the physical diagram would give you a rough idea of the system.

hint: Both systems are in equlibirium.
 
And one more thing. You must show us your attempt to get any further help. If you can't show the attempt, you have to tell us your progress.
 
I multiplied the values first without the error limit. Got 19.38. rounded it off to 2 significant figures since the given data has 2 significant figures. So = 19. For error I used the above formula. It comes out about 1.48. Now my question is. Should I write the answer as 19±1.5 (rounding 1.48 to 2 significant figures) OR should I write it as 19±1. So in short, should the error have same number of significant figures as the mean value or should it have the same number of decimal places as...
Thread 'Calculation of Tensile Forces in Piston-Type Water-Lifting Devices at Elevated Locations'
Figure 1 Overall Structure Diagram Figure 2: Top view of the piston when it is cylindrical A circular opening is created at a height of 5 meters above the water surface. Inside this opening is a sleeve-type piston with a cross-sectional area of 1 square meter. The piston is pulled to the right at a constant speed. The pulling force is(Figure 2): F = ρshg = 1000 × 1 × 5 × 10 = 50,000 N. Figure 3: Modifying the structure to incorporate a fixed internal piston When I modify the piston...
Thread 'A cylinder connected to a hanging mass'
Let's declare that for the cylinder, mass = M = 10 kg Radius = R = 4 m For the wall and the floor, Friction coeff = ##\mu## = 0.5 For the hanging mass, mass = m = 11 kg First, we divide the force according to their respective plane (x and y thing, correct me if I'm wrong) and according to which, cylinder or the hanging mass, they're working on. Force on the hanging mass $$mg - T = ma$$ Force(Cylinder) on y $$N_f + f_w - Mg = 0$$ Force(Cylinder) on x $$T + f_f - N_w = Ma$$ There's also...
Back
Top